A water jet cutter, also known as a water jet or waterjet, is an industrial tool capable of cutting a wide variety of materials using a very high-pressure jet of water, or a mixture of water and an abrasive substance. The term abrasivejet refers specifically to the use of a mixture of water and abrasive to cut hard materials such as metal or granite, while the terms pure waterjet and water-only cutting refer to waterjet cutting without the use of added abrasives, often used for softer materials such as food or rubber.
Waterjet cutting is often used during fabrication of machine parts. It is the preferred method when the materials being cut are sensitive to the high temperatures generated by other methods. Waterjet cutting is used in various industries including mining and aerospace for cutting, shaping, and reaming.
While using high-pressure water for erosion dates back as far as the mid-1800s with hydraulic mining, it was not until the 1930s that narrow jets of water started to appear as an industrial cutting device. In 1933, the Paper Patents Company in Wisconsin developed a paper metering, cutting, and reeling machine that used a diagonally moving waterjet nozzle to cut a horizontally moving sheet of continuous paper. These early applications were at a low pressure and restricted to soft materials like paper.
Waterjet technology evolved in the post-war era as researchers around the world searched for new methods of efficient cutting systems. In 1956, Carl Johnson of Durox International in Luxembourg developed a method for cutting plastic shapes using a thin stream high-pressure waterjet, but those materials, like paper, were soft materials. In 1958, Billie Schwacha of North American Aviation developed a system using ultra high pressure liquid cutting to cut hard materials. This system used a 100,000 psi (690 MPa) pump to deliver a hypersonic liquid jet that could cut high strength alloys such as PH15-7-MO stainless steel. Used as a honeycomb laminate on the Mach 3 XB-70, this cutting method resulted in delaminating at high speed, requiring changes to the manufacturing process.
While not effective for the XB-70 project, the concept was valid and further research continued to evolve waterjet cutting. In 1962, Philip Rice of Union Carbide explored using a pulsing waterjet at up to 50,000 psi (345 MPa) to cut metals, stone, and other materials. Research by S.J. Leach and G.L. Walker in the mid-1960s expanded on traditional coal waterjet cutting to determine ideal nozzle shape for high-pressure waterjet cutting of stone, and Norman Franz in the late 1960s focused on waterjet cutting of soft materials by dissolving long chain polymers in the water to improve the cohesiveness of the jet stream. In the early 1970s, the desire to improve the durability of the waterjet nozzle led Ray Chadwick, Michael Kurko, and Joseph Corrivaeu of the Bendix Corporation to come up with the idea of using corundum crystal to form a waterjet orifice, while Norman Franz expanded on this and created a waterjet nozzle with an orifice as small as 0.002 inches (0.05 mm) that operated at pressures up to 70,000 psi (483 MPa). John Olsen, along with George Hurlburt and Louis Kapcsandy at Flow Research (later Flow Industries), further improved the commercial potential of the waterjet by showing that treating the water beforehand could increase the operational life of the nozzle.
High pressure 
High-pressure vessels and pumps became affordable and reliable with the advent of steam power. By the mid-1800s, steam locomotives were common and the first efficient steam-driven fire engine was operational. By the turn of the century, high-pressure reliability improved, with locomotive research leading to a sixfold increase in boiler pressure, some reaching 1600 psi (11 MPa). Most high-pressure pumps at this time, though, operated around 500–800 psi (3–6 MPa).
High-pressure systems were further shaped by the aviation, automotive, and oil industries. Aircraft manufacturers such as Boeing developed seals for hydraulically boosted control systems in the 1940s, while automotive designers followed similar research for hydraulic suspension systems. Higher pressures in hydraulic systems in the oil industry also led to the development of advanced seals and packing to prevent leaks.
These advances in seal technology, plus the rise of plastics in the post-war years, led to the development of the first reliable high-pressure pump. The invention of Marlex by Robert Banks and John Paul Hogan of the Phillips Petroleum company required a catalyst to be injected into the polyethylene. McCartney Manufacturing Company in Baxter Springs, Kansas, began manufacturing these high-pressure pumps in 1960 for the polyethylene industry. Flow Industries in Kent, Washington set the groundwork for commercial viability of waterjets with John Olsen’s development of the high-pressure fluid intensifier in 1973, a design that was further refined in 1976. Flow Industries then combined the high-pressure pump research with their waterjet nozzle research and brought waterjet cutting into the manufacturing world.
Abrasive waterjet 
While cutting with water is possible, the addition of an abrasive turned the waterjet into a modern machining tool. This began in 1935 when the idea of adding an abrasive to the water stream was developed by Elmo Smith for the field of liquid ablative blasting. Smith’s design was further refined by Leslie Tirrell of the Hydroblast Corporation in 1937, resulting in a nozzle design that created a cohesive mix of high-pressure water and abrasive. Smith and Tirrell’s nozzle design set the groundwork for an efficient abrasive waterjet cutting tool. Producing a commercially viable abrasive waterjet nozzle came next, and an engineering research team at Flow Industries built on their high-pressure pump research, as well as Tirrell’s original nozzle design from the 1930s and Schwacha’s research in high-pressure waterjet cutting from the 1950s, to develop the modern abrasive waterjet nozzle. The final step was creating a durable mixing tube that could withstand the power of the high-pressure abrasivejet, and it was Boride Products (now Kennametal) development of their ROCTEC line of ceramic tungsten carbide composite tubes that significantly increased the operational life of the abrasivejet nozzle.
Waterjet control 
As waterjet cutting moved into traditional manufacturing shops, controlling the cutter reliably and accurately was essential. Early waterjet cutting systems adapted traditional systems such as mechanical pantographs and CNC systems based on John Parsons’ 1952 NC milling machine and running G-code. Challenges inherent to waterjet technology revealed the inadequacies of traditional G-Code, as accuracy depends on varying the speed of the nozzle as it approaches corners and details. Creating motion control systems to incorporate those variables became a major innovation for leading waterjet manufacturers in the early 1990s, with Dr John Olsen of OMAX Corporation developing systems to precisely position the waterjet nozzle while accurately specifying the speed at every point along the path, and also utilizing common PCs as a controller. The largest waterjet manufacturer, Flow International (a spinoff of Flow Industries), recognized the benefits of that system and licensed the OMAX software, with the result that the vast majority of waterjet cutting machines worldwide are simple to use, fast, and accurate.
The cutter is commonly connected to a high-pressure water pump where the water is then ejected from the nozzle, cutting through the material by spraying it with the jet of high-speed water. Additives in the form of suspended grit or other abrasives, such as garnet and aluminium oxide, can assist in this process.
An important benefit of the water jet is the ability to cut material without interfering with its inherent structure, as there is no "heat-affected zone" (HAZ). Minimizing the effects of heat allows metals to be cut without harming or changing intrinsic properties.
Water jet cutters are also capable of producing intricate cuts in material. With specialized software and 3-D machining heads, complex shapes can be produced.
The kerf, or width, of the cut can be adjusted by swapping parts in the nozzle, as well as changing the type and size of abrasive. Typical abrasive cuts have a kerf in the range of 0.04″ to 0.05″ (1.016 to 1.27 mm), but can be as narrow as 0.02″ (0.508 mm). Non-abrasive cuts are normally 0.007″ to 0.013″ (0.178 to 0.33 mm), but can be as small as 0.003″ (0.076 mm), which is approximately that of a human hair. These small jets can permit small details in a wide range of applications.
Water jets are capable of attaining accuracies down to 0.005″ (0.13 mm) and repeatabilities down to 0.001″ (0.025 mm).
Due to its relatively narrow kerf, water jet cutting can reduce the amount of scrap material produced, by allowing uncut parts to be nested more closely together than traditional cutting methods. Water jets use approximately one half to one gallon per minute (depending on the cutting head's orifice size), and the water can be recycled using a closed-loop system. Waste water usually is clean enough to filter and dispose of down a drain. The garnet abrasive is a non-toxic material that can be recycled for repeated use; otherwise, it can usually be disposed in a landfill. Water jets also produce fewer airborne dust particles, smoke, fumes, and contaminants, reducing operator exposure to hazardous materials.
Because the nature of the cutting stream can be easily modified the water jet can be used in nearly every industry; there are many different materials that the water jet can cut. Some of them have unique characteristics that require special attention when cutting.
Materials commonly cut with a water jet include rubber, foam, plastics, leather, composites, stone, tile, metals, food, paper and much more. Materials that cannot be cut with a water jet are tempered glass, diamonds and certain ceramics. Water is capable of cutting materials over eighteen inches (45 cm) thick.
The penetrating power of these tools has led to the exploration of their use as anti-tank weapons but, due to their short range and the advent of composite armour, research was discontinued.
Commercial water jet cutting systems are available from manufacturers all over the world, in a range of sizes, and with water pumps capable of a range of pressures. Typical water jet cutting machines have a working envelope as small as a few square feet, or up to hundreds of square feet. Ultra-high pressure water pumps are available from as low as 40,000 psi (276 MPa) up to 100,000 psi (689 MPa).
There are six main process characteristics to water jet cutting:
- Uses a high velocity stream of abrasive particles suspended in a stream of Ultra High Pressure Water (30,000–90,000 psi) which is produced by a water jet intensifier pump.
- Is used for machining a large array of materials, including heat-sensitive, delicate or very hard materials.
- Produces no heat damage to workpiece surface or edges.
- Nozzles are typically made of sintered boride.
- Produces a taper of less than 1 degree on most cuts, which can be reduced or eliminated entirely by slowing down the cut process.
- Distance of nozzle from workpiece affects the size of the kerf and the removal rate of material. Typical distance is .125″ (3.175 mm).
Temperature is not as much of a factor.
Edge quality 
Edge quality for water jet cut parts is defined with the numbers 1 through 5. Lower numbers indicate rougher edge finish; higher numbers are smoother. For thin materials, the difference in cutting speed for quality 1 could be as much as 3 times faster than the speed for quality 5. For thicker materials, quality 1 could be 6 times faster than quality 5. For example, 4″ thick aluminium Q5 would be 0.72 ipm (18 mm/min) and Q1 would be 4.2 ipm (107 mm/min), 5.8 times faster.
Multi-axis cutting 
With recent advances in control and motion technology, 5-axis water jet cutting (abrasive and pure) has become a reality. Where the normal axes on a water jet are named X (back/forth), Y(left/right) and Z (up/down), a 5-axis system will typically add an A axis (angle from perpendicular) and C axes (rotation around the Z-axis). Depending on the cutting head, the maximum cutting angle for the A axis can be anywhere from 55, 60, or in some cases even 90 degrees from vertical. As such, 5-axis cutting opens up a wide range of applications that can be machined on a water jet cutting machine.
A 5-axis cutting head can be used to cut 4-axis parts, where the bottom surface geometries are shifted a certain amount to produce the appropriate angle and the Z-axis remains at one height. This can be useful for applications like weld preparation where a bevel angle needs to be cut on all sides of a part that will later be welded, or for taper compensation purposes where the kerf angle is transferred to the waste material – thus eliminating the taper commonly found on water jet-cut parts. A 5-axis head can cut parts where the Z-axis is also moving along with all the other axis. This full 5-axis cutting could be used for cutting contours on various surfaces of formed parts.
Because of the angles that can be cut, part programs may need to have additional cuts to free the part from the sheet. Attempting to slide a complex part at a severe angle from a plate can be difficult without appropriate relief cuts.
See also 
- About waterjets, archived from the original on 2010-02-13, retrieved 2010-02-13.
- Fourness, Charles A et al, "Paper Metering, Cutting, and Reeling", filed May 22, 1933, and issued July 2, 1935.
- Johnson, Carl Olof, "Method for Cutting Up Plastic and Semi-Plastic Masses", filed March 13, 1956, and issued April 14, 1959.
- Schwacha, Billie G., "Liquid Cutting of Hard Metals", filed October 13, 1958, and issued May 23, 1961.
- Jenkins, Dennis R & Tony R Landis, Valkyrie: North American's Mach 3 Superbomber, Specialty Press, 2004, p. 108.
- Rice, Phillip K., "Process for Cutting and Working Solid Materials", filed October 26, 1962, and issued October 19, 1965.
- Leach, S.J. and G.L. Walker, "The Application of High Speed Liquid Jets to Cutting", Philosophical Transactions of the Royal Society of London Series A, Mathematical and Physical Sciences, Vol 260, No 1110, July 28, 1966, pp. 295–310.
- Franz, Norman C., "High Velocity Liquid Jet", filed May 31, 1968, and issued August 18, 1970.
- Chadwick, Ray F Chadwick, Michael C Kurko, and Joseph A Corriveau, “Nozzle for Producing Fluid Cutting Jet”, filed March 1, 1971, and issued September 4, 1973.
- Franz, Norman C., “Very High Velocity Fluid Jet Nozzles and Methods of Making Same”, filed July 16, 1971, and issued August 7, 1973.
- Olsen, John H., George H. Hurlburt, and Louis E. Kapcsandy, “Method for Making High Velocity Liquid Jet”, filed June 21, 1976, and issued August 12, 1980.
- "John Ericsson". British Made Steam Fire Engines. Retrieved 10 June 2012.
- Berry, Mitchell M., “Piston Sealing Assembly”, filed March 3, 1941, and issued March 23, 1943.
- Templeton, Herbert W., “Metering Valve Seal”, filed July 11, 1958, and issued July 18, 1961.
- Webb, Derrel D., “High Pressure Packing Means”, filed August 12, 1957, and issued October 17, 1961.
- Hogan, John Paul and Robert L. Banks, “Polymers and Production Thereof”, filed March 26, 1956, and issued March 4, 1958.
- "KMT McCartney Products for the LDPE Industry". KMT McCartney Products. Retrieved 10 June 2012.
- Olsen, John H., “High Pressure Fluid Intensifier and Method”, filed January 12, 1973, and issued May 21, 1974.
- Olsen, John H., “High Pressure Fluid Intensifier and Method”, filed March 16, 1976, and issued June 14, 1977.
- Smith, Elmo V., “Liquid Blasting”, filed June 10, 1935, and issued May 12, 1936.
- Tirrell, Leslie L., “Sandblast Device”, filed April 3, 1937, and issued October 17, 1939.
- Hashish, Mohamed, Michael Kirby and Yih-Ho Pao, “Method and Apparatus for Forming a High Velocity Liquid Abrasive Jet”, filed October 7, 1985, and issued March 10, 1987.
- "ROCTEC Composite Carbide Abrasive Waterjet Nozzles". Kennametal Boride Abrasive Flow Products. Retrieved 1 July 2012.
- "Machining & CNC Manufacturing: A brief history". Worcester Polytechnic Institute. Retrieved 25 June 2012.
- Olsen, John H. "What Really Determines the Time to Make a Part?". Dr Olsen's Lab. Retrieved 28 June 2012.
- Olsen, John H., “Motion Control for Quality in Jet Cutting”, filed May 14, 1997, and issued April 6, 1999.
- Olsen, John H., “Motion Control with Precomputation”, filed October 7, 1993, and issued April 16, 1996.
- "SEC Form 8-K". Flow International Corporation. Retrieved 1 July 2012.
- Lorincz, Jim. "Waterjets: Evolving from Macro to Micro," Manufacturing Engineering, Society of Manufacturing Engineers, November, 2009
- Lorincz, "Waterjets: Evolving from Macro to Micro."
- "Company". Jet Edge. Retrieved 2009-06-11.
- "Company | WARDJet". WARDJet.com. Retrieved 2009-06-11.
- "kmtwaterjet.com". 2010-10-20. Retrieved 2010-10-20.
- "Company | Global Rebar Services". grswaterjet.co.uk. Retrieved 2009-09-08.
- "Waterjet Relationship Parameters".
- "5-Axis Waterjet Cutting".
- Momber, A.W., Kovacevic, R.: Principles of Abrasive Water Jet Machining, Springer, London, 1998.
- How Water Jets Work, HowStuffWorks.com video