digplanet beta 1: Athena
Share digplanet:


Applied sciences






















2-Stroke Engine ani.gif

A two-stroke, or two-cycle, engine is a type of internal combustion engine which completes a power cycle in only one crankshaft revolution and with two strokes, or up and down movements, of the piston in comparison to a "four-stroke engine", which uses four strokes. This is accomplished by the end of the combustion stroke and the beginning of the compression stroke happening simultaneously and performing the intake and exhaust (or scavenging) functions at the same time.

Two-stroke engines often provide high power-to-weight ratio, usually in a narrow range of rotational speeds called the "power band". Compared to 4-stroke engines, they have a greatly reduced number of moving parts, are more compact and significantly lighter.

The first commercial two-stroke engine involving in-cylinder compression is attributed to Scottish engineer Dugald Clerk, who in 1881 patented his design, his engine having a separate charging cylinder. The crankcase-scavenged engine, employing the area below the piston as a charging pump, is generally credited to Englishman Joseph Day.

Gasoline (spark ignition) versions are particularly useful in lightweight (portable) applications such as chainsaws and motorcycles. They are used in diesel compression ignition engines in large and weight insensitive applications, such as ships, locomotives and electricity generation. The heat transfer from the engine to the cooling system is less in a two-stroke engine than in a four-stroke. This adds to the overall engine efficiency. Two-stroke engines have higher exhaust emissions than four-stroke engines.


A two-stroke minibike
Lateral view of a two-stroke Forty series British Seagull outboard engine, the serial number dates it to 1954/1955

The two-stroke petrol (gasoline) engine was very popular throughout the 19th-20th century in motorcycles and small-engined devices, such as chainsaws and outboard motors. They were also used in some cars, a few tractors and many ships. Part of their appeal was their simple design (and resulting low cost) and often high power-to-weight ratio. The lower cost to rebuild and maintain made the two stroke engine incredibly popular, until for the USA their EPA mandated more stringent emission controls in 1978 (taking effect in 1980) and in 2004 (taking effect in 2005 and 2010). The industry largely responded by switching to four-stroke petrol engines, which emit less pollution.[1] Most small designs use petroil (two-stroke oil)) lubrication, with the oil being burned in the combustion chamber, causing "blue smoke" and other types of exhaust pollution. This is a major reason why two-stroke engines were replaced by four-stroke engines in many applications.

Simple two-stroke petrol engines continue to be commonly used in high-power, handheld applications such as string trimmers and chainsaws. The light overall weight, and light-weight spinning parts give important operational and even safety advantages. For example, a four-stroke engine to power a chainsaw operating in any position would be much more expensive and complex than a two-stroke engine that uses a gasoline-oil mixture.

These engines are still preferred for small, portable, or specialized machine applications such as outboard motors, high-performance, small-capacity motorcycles, mopeds, underbones, scooters, tuk-tuks, snowmobiles, karts, ultralights, model airplanes (and other model vehicles), lawnmowers, chain saws, weed-wackers and dirt bikes.

The two-stroke cycle is also used in many diesel engines, most notably large industrial and marine engines, as well as some trucks and heavy machinery.

A number of mainstream automobile manufacturers have used two-stroke engines in the past, including the Swedish Saab and German manufacturers DKW and Auto-Union. The Japanese manufacturer Suzuki did the same in the 1970s.[2] Production of two-stroke cars ended in the 1980s in the West, but Eastern Bloc countries continued until around 1991, with the Trabant and Wartburg in East Germany. Lotus of Norfolk, UK, has a prototype direct-injection two-stroke engine intended for alcohol fuels called the Omnivore[3][4] which it is demonstrating in a version of the Exige.[5] As this uses direct fuel injection, there are dramatic decreases in emission levels and increases in fuel efficiency.

Different two-stroke design types[edit]

A two-stroke engine, in this case with an expansion chamber illustrates the effect of a reflected pressure wave on the fuel charge. This is essential for maximum charge pressure (volumetric efficiency) and fuel efficiency. It is used on most high-performance engine designs.

Although the principles remain the same, the mechanical details of various two-stroke engines differ depending on the type. The design types vary according to the method of introducing the charge to the cylinder, the method of scavenging the cylinder (exchanging burnt exhaust for fresh mixture) and the method of exhausting the cylinder.

Piston-controlled inlet port[edit]

Piston port is the simplest of the designs and the most common in small 2 stroke engines. All functions are controlled solely by the piston covering and uncovering the ports as it moves up and down in the cylinder. In the 1970s, Yamaha worked out some basic principles for this system. They found that, in general, widening an exhaust port increases the power by the same amount as raising the port, but the power band does not narrow as it does when the port is raised. However, there is a mechanical limit to the width of a single exhaust port, at about 62% of the bore diameter for reasonable ring life. Beyond this, the rings will bulge into the exhaust port and wear quickly. A maximum is 70% of bore width is possible in racing engines, where rings are changed every few races. Intake duration is between 120 and 160 degrees. Transfer port time is set at a minimum of 26 degrees. The strong low pressure pulse of a racing 2-stroke expansion chamber can drop the pressure to -7 PSI when the piston is at bottom dead centre, and the transfer ports nearly wide open. One of the reasons for high fuel consumption in 2-strokes is that some of the incoming pressurized fuel/air mixture is forced across the top of the piston, where it has a cooling action, and straight out the exhaust pipe. An expansion chamber with a strong reverse pulse will stop this out-going flow.[6] A fundamental difference from typical four-stroke engines is that the two-stroke's crankcase is sealed and forms part of the induction process in gasoline and hot bulb engines. Diesel two-strokes often add a Roots blower or piston pump for scavenging.

Reed inlet valve[edit]

Main article: Reed valve
A Cox Babe Bee 0.049 cubic inch (0.8 cubic cm) reed valve engine, disassembled, uses glow plug ignition. The mass is 64 grams.

The reed valve is a simple but highly effective form of check valve commonly fitted in the intake tract of the piston-controlled port. They allow asymmetric intake of the fuel charge, improving power and economy, while widening the power band. They are widely used in motorcycle, ATV and marine outboard engines.

Rotary inlet valve[edit]

The intake pathway is opened and closed by a rotating member. A familiar type sometimes seen on small motorcycles is a slotted disk attached to the crankshaft which covers and uncovers an opening in the end of the crankcase, allowing charge to enter during one portion of the cycle.

Another form of rotary inlet valve used on two-stroke engines employs two cylindrical members with suitable cutouts arranged to rotate one within the other - the inlet pipe having passage to the crankcase only when the two cutouts coincide. The crankshaft itself may form one of the members, as in most glow plug model engines. In another embodiment, the crank disc is arranged to be a close-clearance fit in the crankcase, and is provided with a cutout which lines up with an inlet passage in the crankcase wall at the appropriate time, as in the Vespa motor scooter.

The advantage of a rotary valve is it enables the two-stroke engine's intake timing to be asymmetrical, which is not possible with piston port type engines. The piston port type engine's intake timing opens and closes before and after top dead center at the same crank angle, making it symmetrical, whereas the rotary valve allows the opening to begin earlier and close earlier.

Rotary valve engines can be tailored to deliver power over a wider speed range or higher power over a narrower speed range than either piston port or reed valve engine. Where a portion of the rotary valve is a portion of the crankcase itself, it is particularly important that no wear is allowed to take place.


Deflector piston with cross-flow scavenging

In a cross-flow engine, the transfer and exhaust ports are on opposite sides of the cylinder, and a deflector on the top of the piston directs the fresh intake charge into the upper part of the cylinder, pushing the residual exhaust gas down the other side of the deflector and out the exhaust port.[7] The deflector increases the piston's weight and exposed surface area, affecting piston cooling and also making it difficult to achieve an efficient combustion chamber shape. This design has been superseded since the 1960s by the loop scavenging method (below), especially for motorbikes, although for smaller or slower engines, such as lawn mowers, the cross-flow-scavenged design can be an acceptable approach.


The Two-stroke cycle
 A: intake/scavenging 
 B: Exhaust 
 C: Compression 
 D: Expansion (power) 
Main article: Schnuerle porting

This method of scavenging uses carefully shaped and positioned transfer ports to direct the flow of fresh mixture toward the combustion chamber as it enters the cylinder. The fuel/air mixture strikes the cylinder head, then follows the curvature of the combustion chamber, and then is deflected downward.

This not only prevents the fuel/air mixture from traveling directly out the exhaust port, but also creates a swirling turbulence which improves combustion efficiency, power and economy. Usually, a piston deflector is not required, so this approach has a distinct advantage over the cross-flow scheme (above).

Often referred to as "Schnuerle" (or "Schnürle") loop scavenging after the German inventor of an early form in the mid-1920s, it became widely adopted in that country during the 1930s and spread further afield after World War II.

Loop scavenging is the most common type of fuel/air mixture transfer used on modern two-stroke engines. Suzuki was one of the first manufacturers outside of Europe to adopt loop-scavenged two-stroke engines. This operational feature was used in conjunction with the expansion chamber exhaust developed by German motorcycle manufacturer, MZ and Walter Kaaden.

Loop scavenging, disc valves and expansion chambers worked in a highly coordinated way to significantly increase the power output of two-stroke engines, particularly from the Japanese manufacturers Suzuki, Yamaha and Kawasaki. Suzuki and Yamaha enjoyed success in grand Prix motorcycle racing in the 1960s due in no small way to the increased power afforded by loop scavenging.

An additional benefit of loop scavenging was the piston could be made nearly flat or slightly dome shaped, which allowed the piston to be appreciably lighter and stronger, and consequently to tolerate higher engine speeds. The "flat top" piston also has better thermal properties and is less prone to uneven heating, expansion, piston seizures, dimensional changes and compression losses.

SAAB built 750 and 850 cc 3-cylinder engines based on a DKW design that proved reasonably successful employing loop charging. The original SAAB 92 had a two-cylinder engine of comparatively low efficiency. At cruising speed, reflected wave exhaust port blocking occurred at too low a frequency. Using the asymmetric three-port exhaust manifold employed in the identical DKW engine improved fuel economy.

The 750 cc standard engine produced 36 to 42 hp, depending on the model year. The Monte Carlo Rally variant, 750 cc (with a filled crankshaft for higher base compression), generated 65 hp. An 850 cc version was available in the 1966 SAAB Sport (a standard trim model in comparison to the deluxe trim of the Monte Carlo). Base compression comprises a portion of the overall compression ratio of a two-stroke engine. Work published at SAE in 2012 points that loop scavenging is under every circumstance more efficient than cross-flow scavenging.


Uniflow scavenging
The Uniflow Two-stroke cycle
1=TDC (Diesel injection is usually initiated at 4° BTDC)
 A: Intake (effective scavenging ≈ 135°-225°; necessarily symmetric about BDC) 
 B: Exhaust (not necessarily symmetric) 
 C: Compression (not necessarily symmetric) 
 D: Expansion (power; not necessarily symmetric) 

In a uniflow engine, the mixture, or "charge air" in the case of a diesel, enters at one end of the cylinder controlled by the piston and the exhaust exits at the other end controlled by an exhaust valve or piston. The scavenging gas-flow is therefore in one direction only, hence the name uniflow. The valved arrangement is common in on-road, off-road and stationary two-stroke engines (Detroit Diesel), certain small marine two-stroke engines (Gray Marine), certain railroad two-stroke diesel locomotives (Electro-Motive Diesel) and large marine two-stroke main propulsion engines (Wärtsilä). Ported types are represented by the opposed piston design in which there are two pistons in each cylinder, working in opposite directions such as the Junkers Jumo and Napier Deltic.[8] The once-popular split-single design falls into this class, being effectively a folded uniflow. With advanced angle exhaust timing, uniflow engines can be supercharged with a crankshaft-driven (piston[9] or Roots) blower.

Stepped piston engine[edit]

The piston of this engine is "top-hat" shaped; the upper section forms the regular cylinder, and the lower section performs a scavenging function. The units run in pairs, with the lower half of one piston charging an adjacent combustion chamber.

This system is still partially dependent on total loss lubrication (for the upper part of the piston), the other parts being sump lubricated with cleanliness and reliability benefits. The piston weight is only about 20% heavier than a loop-scavenged piston because skirt thicknesses can be less. Bernard Hooper Engineering Ltd. (BHE) is one of the more recent engine developers using this approach.[10]

Power valve systems[edit]

Many modern two-stroke engines employ a power valve system. The valves are normally in or around the exhaust ports. They work in one of two ways: either they alter the exhaust port by closing off the top part of the port, which alters port timing, such as Ski-doo R.A.V.E, Yamaha YPVS, Honda RC-Valve, Kawasaki K.I.P.S., Cagiva C.T.S. or Suzuki AETC systems, or by altering the volume of the exhaust, which changes the resonant frequency of the expansion chamber, such as the Suzuki SAEC and Honda V-TACS system. The result is an engine with better low-speed power without sacrificing high-speed power. However as power valves are in the hot gas flow they need regular maintenance to perform well.

Direct injection[edit]

Direct injection has considerable advantages in two-stroke engines, eliminating some of the waste and pollution caused by carbureted two-strokes where a proportion of the fuel/air mixture entering the cylinder goes directly out, unburned, through the exhaust port. Two systems are in use, low-pressure air-assisted injection, and high pressure injection.

Since the fuel does not pass through the crankcase, a separate source of lubrication is needed.

Two-stroke diesel engine[edit]

Brons two-stroke V8 Diesel engine driving a Heemaf generator.

Diesel engines rely solely on the heat of compression for ignition. In the case of Schnuerle ported and loop-scavenged engines, intake and exhaust happens via piston-controlled ports. A uniflow diesel engine takes in air via scavenge ports, and exhaust gases exit through an overhead poppet valve. Two-stroke diesels are all scavenged by forced induction. Some designs use a mechanically driven Roots blower, whilst marine diesel engines normally use exhaust-driven turbochargers, with electrically-driven auxiliary blowers for low-speed operation when exhaust turbochargers are unable to deliver enough air.

Marine two-stroke diesel engines directly coupled to the propeller are able to start and run in either direction as required. The fuel injection and valve timing is mechanically readjusted by using a different set of cams on the camshaft. Thus, the engine can be run in reverse to move the vessel backwards.


Most small petrol two-stroke engines cannot be lubricated by oil contained in their crankcase and sump, since the crankcase is already being used to pump fuel-air mixture into the cylinder. Traditionally, the moving parts (both rotating crankshaft and sliding piston) were lubricated by a premixed fuel-oil mixture (at a ratio between 16:1 and 100:1). As late as the 1970s, petrol stations would often have a separate pump to deliver such a premix fuel to motorcycles. Even then, in many cases, the rider would carry a bottle of their own two-stroke oil. Taking care to close the fuel-tap first, he or she would meter in a little oil (using the cap of the bottle) and then put in the petrol, this action mixing the two liquids. Two-stroke oils which became available worldwide in the 1970s are specifically designed to mix with petrol and be burnt in the combustion chamber without leaving undue unburnt oil or ash. This led to a marked reduction in spark plug fouling, which had been a factor in two-stroke engines.

More recent two-stroke engines might pump lubrication from a separate tank of two stroke oil. The supply of this oil is controlled by the throttle position. An example machine is Yamaha's PW80 (Pee-wee), a small, 80cc two stroke dirt bike designed for young children. The technology is referred to as auto-lube. This is still a total-loss system with the oil being burnt the same as in the pre-mix system, however given that the oil is not properly mixed with the fuel when burned in the combustion chamber, it translates into a slightly more efficient lubrication. This lubrication method also pays dividends in terms of user friendliness by eliminating the need to mix the gasoline constantly, makes the motor much less susceptible to atmospheric conditions (Ambient temperature, elevation) and ensures a constant, unvarying fuel-oil ratio in the combustion chamber. However, this method of lubrication is still ultimately the same as premixed gasoline in that the oil is still burnt (albeit not as completely as pre-mix) and the gas is still mixed with the oil, although not as thoroughly as in pre-mix. In addition, this method requires extra mechanical parts to pump the oil from the separate tank, to the carburetor or throttle body. In applications where performance, simplicity and/or dry weight are significant considerations, the pre-mix lubrication method is almost always used. For example a two stroke engine in a motocross bike, pays major consideration to performance, simplicity and weight. Chainsaws must be as light as possible to reduce user fatigue and hazard, especially when used in a professional work environment and the same could be said for brush cutters.

All two-stroke engines running on a petrol/oil mix will suffer oil starvation if forced to rotate at speed with the throttle closed, e.g. motorcycles descending long hills and perhaps when decelerating gradually from high speed by changing down through the gears. Two-stroke cars (such as those that were popular in Eastern Europe in mid-20th century) were in particular danger and were usually fitted with freewheel mechanisms in the powertrain, allowing the engine to idle when the throttle was closed, requiring the use of the brakes in all slowing situations.

Large two-stroke engines, including diesels, normally use a sump lubrication system similar to four-stroke engines. The cylinder must still be pressurized, but this is not done from the crankcase, but by an ancillary Roots-type blower or a specialized turbocharger (usually a turbo-compressor system) which has a "locked" compressor for starting (and during which it is powered by the engine's crankshaft), but which is "unlocked" for running (and during which it is powered by the engine's exhaust gases flowing through the turbine).

Two-stroke reversibility[edit]

For the purpose of this discussion, it is convenient to think in motorcycle terms, where the exhaust pipe faces into the cooling air stream, and the crankshaft commonly spins in the same axis and direction as do the wheels i.e. "forward". Some of the considerations discussed here apply to four-stroke engines (which cannot reverse their direction of rotation without considerable modification), almost all of which spin forward, too.

Regular gasoline two-stroke engines will run backwards for short periods and under light load with little problem, and this has been used to provide a reversing facility in microcars, such as the Messerschmitt KR200, that lacked reverse gearing. Where the vehicle has electric starting, the motor will be turned off and restarted backwards by turning the key in the opposite direction. Two-stroke golf carts have used a similar kind of system. Traditional flywheel magnetos (using contact-breaker points, but no external coil) worked equally well in reverse because the cam controlling the points is symmetrical, breaking contact before top dead centre (TDC) equally well whether running forwards or backwards. Reed-valve engines will run backwards just as well as piston-controlled porting, though rotary valve engines have asymmetrical inlet timing and will not run very well.

There are serious disadvantages to running any engine backwards under load for any length of time, and some of these reasons are general, applying equally to both two-stroke and four-stroke engines. Some of this disadvantage is intrinsic, unavoidable even in the case of a complete re-design. The problem comes about because in "forwards" running the major thrust face of the piston is on the back face of the cylinder which, in a two-stroke particularly, is the coolest and best lubricated part. The forward face of the piston is less well-suited to be the major thrust face since it covers and uncovers the exhaust port in the cylinder, the hottest part of the engine, where piston lubrication is at its most marginal. The front face of the piston is also more vulnerable since the exhaust port, the largest in the engine, is in the front wall of the cylinder. Piston skirts and rings risk being extruded into this port, so it is always better to have them pressing hardest on the back wall (where there are only the transfer ports) and there is good support. In some engines, the small end is offset to reduce thrust in the intended rotational direction and the forward face of the piston has been made thinner and lighter to compensate - but when running backwards, this weaker forward face suffers increased mechanical stress it was not designed to resist.[11]

Large two-stroke ship diesels are sometimes made to be reversible. Like four-stroke ship engines (some of which are also reversible) they use mechanically-operated valves, so require additional camshaft mechanisms.

On top of other considerations, the oil-pump of a modern two-stroke may not work in reverse, in which case the engine will suffer oil starvation within a short time. Running a motorcycle engine backwards is relatively easy to initiate, and in rare cases, can be triggered by a back-fire. It is not advisable.

Model airplane engines with reed-valves can be mounted in either tractor or pusher configuration without needing to change the propeller. These motors are compression ignition, so there are no ignition timing issues and little difference between running forward and running backward.

See also[edit]


  1. ^ http://www.epa.gov/nonroad/proposal/r01049.pdf
  2. ^ "Suzuki LJ50 INFO". Lj10.com. Retrieved 2010-11-07. 
  3. ^ "Lotus, QUB and Jaguar to Develop Variable Compression Ratio, 2-Stroke OMNIVORE Research Engine". Green Car Congress. 2008-08-12. Retrieved 2010-11-07. 
  4. ^ "Lotus Engineering Omnivore Variable Compression Ratio Engine to Debut in Geneva". Wot.motortrend.com. Retrieved 2010-11-07. 
  5. ^ Korzeniewski, Jeremy (2008-08-12). "Lotus developing efficient two-stroke OMNIVORE engine". Autoblog. Retrieved 2010-11-07. 
  6. ^ Gordon Jennings. Guide to 2 stroke port timing. Jan 1973
  7. ^ Irving, P.E. (1967). Two-Stroke Power Units. Newnes. pp. 13–15. 
  8. ^ "junkers". Iet.aau.dk. Retrieved 2009-06-06. [dead link]
  9. ^ Junkers truck engine 1933.
  10. ^ BHE - Stepped Piston Engine
  11. ^ Ross and Ungar, "On Piston Slap as a Source of Engine Noise," ASME Paper
  • Frank Jardine (Alcoa): "Thermal Expansion in Automotive-Engine Design", SAE paper 300010
  • G P Blair et al. (Univ of Belfast), R Fleck (Mercury Marine), "Predicting the Performance Characteristics of Two-Cycle Engines Fitted with Reed Induction Valves", SAE paper 790842
  • G Bickle et al. (ICT Co), R Domesle et al. (Degussa AG): "Controlling Two-Stroke Engine Emissions", Automotive Engineering International (SAE) Feb 2000:27-32.
  • BOSCH, "Automotive Manual", 2005, Section: Fluid's Mechanics, Table 'Discharge from High-Pressure Deposits'.

External links[edit]

Original courtesy of Wikipedia: http://en.wikipedia.org/wiki/Two-stroke_engine — Please support Wikipedia.
This page uses Creative Commons Licensed content from Wikipedia. A portion of the proceeds from advertising on Digplanet goes to supporting Wikipedia.

32 news items

PR Web (press release)
Mon, 18 Aug 2014 07:48:45 -0700

Recreational boaters can trade in their old two-stroke engine in exchange for a ten percent discount towards the purchase of a new Honda four-stroke outboard engine. All old and inefficient two-stroke engines collected will be responsibly recycled ...
Midland Daily News
Tue, 05 Aug 2014 16:40:34 -0700

Summerhill Impact, in partnership with Honda Canada Inc. and supported by Environment Canada, are running the Clean Wake Program across Ontario until August 31, 2014. Recreational boaters can trade in their old two-stroke engine in exchange for a ten ...

Dallas Morning News

Dallas Morning News
Sat, 30 Aug 2014 08:45:00 -0700

Unlike motorcycles, mopeds have pedals, which are used to jump-start the two-stroke engine that emits a gassy smell reminiscent of lawn mowers. Most have top speeds around 20 mph, although tricked out, they can hit 60. But they're hardly sturdy. Mopeds ...
Aitkin Independent Age
Thu, 28 Aug 2014 04:37:30 -0700

He said a day's ride on his two-stroke engine costs about $25 for seven gallons of gas. Of course, a day's ride on Mille Lacs could cost a bit more after stopping at bars and resorts for food and drink. Zigo said he enjoys spending time traveling ...
Fri, 29 Aug 2014 02:54:28 -0700

It had decided against a two-stroke engine system “given the additional risks that this will generate for the company.” John Fredriksen's Geveran Trading has recently built up a 16.1% holding in Flex, whose vessels are identified by analysts as the ...
Wed, 06 Aug 2014 06:47:19 -0700

Worldwide market for Biolubricant product categories explored in this study includes Hydraulic Fluids, Metalworking Fluids, Chainsaw Lubricants, Mold Release Agents, Gear Oils, Two-Stroke Engine Oils and Greases. The report also focuses on end-use ...


Sat, 23 Aug 2014 22:41:14 -0700

The Trabi's interior was as basic as its two-stroke engine. Think car abandoned in bad neighborhood for a couple of hours – but without the broken windows and the dangling wires where the radio used to be. There was no radio. The dashboard, in fact, ...

Bognor Regis Observer

Bognor Regis Observer
Thu, 28 Aug 2014 05:22:30 -0700

Between 10am on August 21 and 9am on August 25 a fishing boat and trailer were stolen from the driveway of a property in Frandor Road. The boat has been described as a Dejon fishing boat with two outboard motors and a Suzuki 40 two stroke engine.

Oops, we seem to be having trouble contacting Twitter

Talk About Two-stroke engine

You can talk about Two-stroke engine with people all over the world in our discussions.

Support Wikipedia

A portion of the proceeds from advertising on Digplanet goes to supporting Wikipedia. Please add your support for Wikipedia!