digplanet beta 1: Athena
Share digplanet:


Applied sciences






















For the sleeve valve used in water applications, see Sleeve valve (water).
Bristol Perseus

The sleeve valve is a type of valve mechanism for piston engines, distinct from the usual poppet valve. Sleeve-valve engines saw use in a number of pre-World War II luxury cars and in USA in the Willys-Knight car and light truck. They subsequently fell from use due to advances in poppet-valve technology, including sodium cooling, and the double sleeve Knight system engine's tendency to burn a lot of lubricating oil or to seize due to lack of it. The Scottish Argyll company used its own, much simpler and efficient, single-sleeve system (Burt-McCollum) in its cars, a system which, after extensive development, saw substantial use in British aircraft engines of the 1940s, such as the Napier Sabre and Bristol Hercules and Centaurus, only to be supplanted by the jet engine.


A sleeve valve takes the form of one or more machined sleeves. It fits between the piston and the cylinder wall in the cylinder of an internal combustion engine where it rotates and/or slides. Ports (holes) in the side of the sleeve(s) come into alignment with the cylinder's inlet and exhaust ports at the appropriate stages in the engine's cycle.

Types of sleeve valve[edit]

A 4-cylinder car engine of 1919, sectioned through the cylinders to show the Knight sleeve valves.
Knight sleeve-valve engine

The first successful sleeve valve was patented by Charles Yale Knight, and used twin alternating sliding sleeves. It was used in some luxury automobiles, notably Willys, Daimler, Mercedes-Benz, Minerva, Panhard, Peugeot and Avions Voisin. The higher oil consumption[1] was heavily outweighed by the quietness of running and the very high mileages without servicing. Early poppet-valve systems required decarbonization at very low mileages.

Diagram of the Argyll single sleeve valve, showing the complex shape of the multiple ports and the semi-rotary actuation
Argyll single sleeve valve

The Burt-McCollum sleeve valve, as used by the Scottish company Argyll for its cars,[2] and later adopted by Bristol for its radial aircraft engines, used a single sleeve which rotated around a timing axle set at 90 degrees to the cylinder axis. Mechanically simpler and more rugged, the Burt-McCollum valve had the additional advantage of reducing oil consumption (compared to other sleeve valve designs), while retaining the rational combustion chambers and big, uncluttered, porting area possible in the Knight system.

A small number of designs used a "cuff" sleeve in the cylinder head instead of the cylinder proper,[3] providing a more "classic" layout compared to traditional poppet valve engines. This design also had the advantage of not having the piston within the sleeve, although in practice this appears to have had little practical value. On the downside, this arrangement limited the size of the ports to that of the cylinder head, whereas in-cylinder sleeves could have much larger ports.



The main advantages of the sleeve-valve engine are:

  • High volumetric efficiency due to very large port openings. Sir Harry Ricardo also demonstrated better mechanical and thermal efficiency.
  • The size of the ports can be readily controlled. This is important when an engine operates over a wide RPM range, since the speed at which air can enter and exit the cylinder is defined by the size of the duct leading to the cylinder, and varies according to the cube of the RPM. In other words, at higher RPM the engine typically requires larger ports that remain open for a greater proportion of the cycle, which is fairly easy to achieve with sleeve valves, but difficult in a poppet valve system.
  • Good exhaust scavenging and controllable swirl of the inlet air/fuel mixture in single-sleeve designs. When the intake ports open, the air/fuel mixture can be made to enter tangentially to the cylinder. This helps scavenging when exhaust/inlet timing overlap is used and a wide speed range required, whereas poor poppet valve exhaust scavenging can dilute the fresh air/fuel mixture intake to a greater degree, being more speed dependent (relying principally on exhaust/inlet system resonant tuning to separate the two streams). Greater freedom of combustion chamber design (few constraints other than the spark plug positioning) means that fuel/air mixture swirl at top dead center (TDC) can also be more controlled allowing improved ignition and flame travel which, as demonstrated by Ricardo, allows at least one extra unit of compression ratio before detonation, compared with the poppet valve engine.
  • The combustion chamber formed with the sleeve at the top of its stroke is ideal for complete, detonation-free combustion of the charge, as it does not have to contend with compromised chamber shape and hot exhaust (poppet) valves.
  • No springs are involved in the sleeve valve system, therefore the power needed to operate the valve remains largely constant with the engine's RPM, meaning that the system can be used at very high speeds with no penalty for doing so. A problem with high-speed engines that use poppet valves is that as engine speed increases, the speed at which the valve moves also has to increase. This in turn increases the loads involved due to the inertia of the valve, which has to be opened quickly, brought to a stop, then reversed in direction and closed and brought to a stop again. Large valves that allow good air-flow have considerable mass and require a strong spring to overcome the opening inertia. At some point, the valve spring reaches its resonance frequency, causing a compression wave to oscillate within the spring that, in turn, causes it to become effectively weaker and unable to properly close the valve. This valve float can result in the valve not closing quickly and it may strike the top of the rising piston. In addition, camshaft, pushrods, and valve rockers can be eliminated in a sleeve valve design, as the sleeve valves are generally driven by a single gear powered from the crankshaft. In an aircraft engine, this provided desirable reductions in weight and complexity.
  • Longevity, as demonstrated in early automotive applications of the Knight engine. Prior to the advent of leaded gasolines, poppet-valve engines typically required grinding of the valves and valve seats after 20,000 to 30,000 miles (32,000 to 48,000 km) of service. Sleeve valves did not suffer from the wear and recession caused by the repetitive impact of the poppet valve against its seat. Sleeve valves were also subjected to less intense heat buildup than poppet valves, owing to their greater area of contact with other metal surfaces. In the Knight engine, carbon build-up actually helped to improve the sealing of the sleeves, the engines said to "improve with use", in contrast to poppet valve engines, which lose compression and power as valves, valve stems and guides wear. Due to the continuous motion of the sleeve (Burt-McCollum type), the high wear points linked to poor lubrication in the TDC/BDC (bottom dead center) of piston travel within the cylinder are suppressed, so rings and cylinders lasted much longer.
  • The cylinder head is not required to house valves, allowing the spark plug to be placed in the best possible location for efficient ignition of the combustion mixture. For very big engines, where flame propagation speed limits both size and speed, the swirl induced by ports as described by Ricardo can be an additional advantage. In his research with Two-Stroke Single Sleeve-Valve Compression Ignition engines, Harry Ricardo proved that an open Sleeve was feasible, acting as a second piston that transmitted 3% of the power to the output shaft through the Sleeve driving mechanism, this highly simplifies construction, as the 'Junk head' is no longer needed.
  • Lower operating temperatures of all power-connected engine parts, cylinder and pistons, Harry Ricardo showed that as long as the clearance between sleeve and cylinder is adequately settled, and the lubricating oil film is thin enough, Sleeves are 'transparent to heat'.
  • Continental in the United States conducted extensive research in single-sleeve-valve engines, pointing that they were eventually of lower production cost, and easier to produce. However, their aircraft engines soon equalled the single-sleeve-valve engines' performance by introducing improvements such as sodium-cooled poppet valves, and it seems also that the costs of this research, along with the October 1929 crisis, led to the Continental single-sleeve-valve engines not entering mass production. A book (Continental! Its motors and its people. W Wagner, 1983. ISBN 0-8168-4506-9) on Continental Engines reports that General Motors had conducted tests with single-sleeve-valve engines, rejecting this kind of arrangement, and, according to M Hewland (Car&Driver, July 1974) also Ford around 1959.

Most of these advantages were evaluated and established during the 1920s by Roy Fedden and Harry Ricardo, possibly the sleeve-valve engine's greatest advocate. He conceded that some of these advantages were significantly eroded as fuels improved up to and during World War II and as sodium-cooled exhaust valves were introduced in high output aircraft engines.


A number of disadvantages plagued the single sleeve valve:

  • Perfect, even very good, sealing is difficult to achieve. In a poppet valve engine, the piston possesses piston rings (at least three and sometimes as many as eight) which form a seal with the cylinder bore. During the "breaking in" period (known as "running-in" in the UK) any imperfections in one are scraped into the other, resulting in a good fit. This type of "breaking in" is not possible on a sleeve-valve engine, however, because the piston and sleeve move in different directions and in some systems even rotate in relation to one another. Unlike a traditional design, the imperfections in the piston do not always line up with the same point on the sleeve. In the 1940s this was not a major concern because the poppet valve stems of the time typically leaked appreciably more than they do today, so that oil consumption was significant in either case. To one of the 1922–1928 Argyll Single Sleeve Valve engines, the 12, a four-cylinder 91 cu in (1,491 cc) unit, was attributed an oil consumption of one gallon for 1,945 miles,[4] and 1,000 miles per gallon of oil in the 15/30 4 cylinder 159 cu in (2,610 cc).[5] Mike Hewland in 1974 claimed that the progress in lubricating oils, materials, and machining had solved the oil thirst problem, his experimental 500 cc Single Cylinder engines using less oil than its contemporary poppet valve 'competitors'. Single-Sleeve-Valve engines had a reputation of being much less smoky than the Daimler with engines of Knight double-sleeve engines counterparts.
  • The high oil consumption problem associated with the Knight double sleeve valve was fixed with the Burt-McCollum Single Sleeve Valve, as perfected by Bristol. At top dead center (TDC), the single-sleeve valve rotates in relation to the piston. This prevents boundary lubrication problems, as piston ring ridge wear at TDC and bottom dead center (BDC) does not occur. The Bristol Hercules overhaul life was rated at 3,000 hours.[6]
  • An inherent disadvantage is that the piston in its course partially obscures the ports, thus making it difficult for gases to flow during the crucial overlap between the intake and exhaust valve timing usual in modern engines. The 1954 printing of the book by Harry Ricardo: 'The high-speed internal combustion engine', and also some patents on Sleeve-valve production, point that the available zone for ports in the Sleeve depends on the type of Sleeve drive and Bore/Stroke ratio. The German born engineer Max Bentele, after studying a British sleeve valve aero engine (probably a Hercules), complained that the arrangement required more than 100 gearwheels for the engine, too many for his taste.[7]
  • A serious issue with large single-sleeve aero-engines is that their maximum reliable rotational speed is limited to about 3000 RPM.
  • Improved fuel octanes, above about 87 RON, have assisted poppet-valve engines’ power output more than single-sleeve engines’.[citation needed]
  • The increased difficulty with oil consumption and cylinder-assembly lubrication has never been solved.
  • If stored horizontally, sleeves tend to ovalize, producing several types of mechanical problems. To avoid this, special cabinets were developed to store sleeves vertically.


Charles Yale Knight[edit]

Daimler 22 hp[8] open 2-seater (1909 example). The clearly visible mascot on its radiator cap is (C. Y.'s) Knight

In 1901 Knight bought an air-cooled, single-cylinder three-wheeler whose noisy valves annoyed him. He believed that he could design a better engine and did so, inventing his double sleeve principle in 1904. Backed by Chicago entrepreneur L.B. Kilbourne, a number of engines were constructed followed by the "Silent Knight" touring car which was shown at the 1906 Chicago Auto Show.

Knight's design had two cast-iron sleeves per cylinder, one sliding inside the other with the piston inside the inner sleeve. The sleeves were operated by small connected rods actuated by an eccentric shaft. They had ports cut out at their upper ends. The design was remarkably quiet, and the sleeve valves needed little attention. It was, however, more expensive to manufacture due to the precision grinding required on the sleeves' surfaces. It also used more oil at high speeds and was harder to start in cold weather.[9]

Although he was initially unable to sell his Knight Engine in the United States, a long sojourn in England, involving extensive further development and refinement by Daimler supervised by their consultant Dr Frederick Lanchester[10] eventually secured Daimler and several luxury car firms as customers willing to pay his expensive premiums. He first patented the design in England in 1908. As part of the licensing agreement, "Knight" was to be included in the car's name.

Six cylinder Daimler sleeve valve engines were used in the first British tanks in WW1, up to and including the Mark IV. As a result of the tendency of the engines to smoke and hence give away the tank positions, Harry Ricardo was brought in, and devised a new engine which replaced the sleeve valve starting with the Mark V tank.

Among the companies using Knight's technology were Avions Voisin, Daimler (1909–1930s) including their V12 Double Six, Panhard (1911–39), Mercedes (1909–24), Willys (as the Willys-Knight, plus the associated Falcon-Knight), Stearns, Mors, Peugeot, and Belgium's Minerva company that was forced to stop its sleeve-valve line of engines as a result of the limitations imposed on them by the winners of WWII, some thirty companies in all.[11] Itala also experimented with sleeve valves.[citation needed]

Upon Knight's return to America he was able to get some firms to use his design; here his brand name was "Silent Knight" (1905–1907) — the selling point was that his engines were quieter than those with standard poppet valves. The best known of these were the F.B. Stearns Company of Cleveland, which sold a car named the Stearns-Knight, and the Willys firm which offered a car called the Willys-Knight, which was produced in far greater numbers than any other sleeve-valve car.


The Burt-McCollum sleeve valve, having its name from the surnames of the two engineers that patented the same concept with weeks of difference, Peter Burt and James Harry Keighly McCollum, patent applications are of August 6 and June 22, 1909, respectively, both engineers hired by the Scottish car maker Argyll, consisted of a single sleeve, which was given a combination of up-and-down and partial rotary motion. It was developed in about 1909 and was first used in the 1911 Argyll car. The initial 1900 investment in Argyll was ₤15,000 and building the magnificent Scotland plant cost ₤500,000 in 1920. It is reported that litigation by the owners of the Knight patents cost Argyll ₤50,000, perhaps one of the reasons for the temporary shutdown of their plant. Another car maker that used the Argyll SSV patents was Piccard-Pictet (Pic-Pic); Louis Chevrolet and others founded Frontenac Motors in 1923 with the aim of producing an 8-L SSV engined luxury car, but this never reached production for reasons connected to the time limits to the Argyll patents in the USA. The greatest success for single sleeve valves (SSV) was in Bristol's large aircraft engines and they were also used in the Napier Sabre and Rolls-Royce Eagle engines. The SSV system also reduced the high oil consumption associated with the Knight double sleeve valve.[12]

Barr and Stroud Ltd of Anniesland, Glasgow also licensed the SSV design, and made small versions of the engines that they marketed to motor cycle companies. In an advertisement in Motor Cycle magazine in 1922[13] Barr & Stroud promoted their 350cc sleeve valve engine and listed Beardmore-Precision, Diamond, Edmund, and Royal Scot as motocycle manufacturers offering it. This engine had been described in the March edition as the 'Burt' engine.[14] Grindlay-Peerless started producing a SSV Barr & Stroud engined 999cc V-twin in 1923 [1] and later added a 499cc single SSV as well as the 350cc.

A number of sleeve valve aircraft engines were developed following a seminal 1927 research paper from the RAE by Harry Ricardo. This paper outlined the advantages of the sleeve valve and suggested that poppet valve engines would not be able to offer power outputs much beyond 1500 hp (1,100 kW). Napier and Bristol began the development of sleeve-valve engines that would eventually result in limited production of two of the most powerful piston engines in the world: the Napier Sabre and Bristol Centaurus.

Potentially the most powerful of all sleeve-valve engines (though it never reached production) was the Rolls-Royce Crecy V-12 (oddly, using a 90-degree V-angle), two-stroke, direct-injected, turbocharged (force-scavenged) aero-engine of 26.1 litres capacity. It achieved a very high specific output, and surprisingly good specific fuel consumption (SFC). In 1945 the single-cylinder test-engine (E65) produced the equivalent of 5,000 HP (192 BHP/Litre) when water injected, although the full V12 would probably have been initially type rated at circa 2,500 hp (1,900 kW). Sir Harry Ricardo, who specified the layout and design goals, felt that a reliable 4,000 HP military rating would be possible. Ricardo was constantly frustrated during the war with Rolls-Royce's (RR) efforts. Hives & RR were very much focused on their Merlin, Griffon then Eagle and finally Whittle's jets, which all had a clearly defined production purpose. Ricardo and Tizard eventually realized that the Crecy would never get the development attention it deserved unless it was specified for installation in a particular aircraft but by 1945, their "Spitfire on steroids" concept of a rapidly climbing interceptor powered by the lightweight Crecy engine had become an aircraft without a purpose.

Following World War II, the sleeve valve became utilised less, just the French SNECMA produced some SSV engines under Bristol license that were installed in the Noratlas transport airplane, also another transport aircraft, the Azor built by the Spanish CASA installed SSV Bristol engines post-WWII. Bristol sleeve valve engines were used however during the post-war air transport boom, in the Vickers Viking and related military Varsity and Valetta, Airspeed Ambassador, used on BEA's European routes, and Handley Page Hermes (and related military Hastings), and Short Solent airliners and the Bristol Freighter and Superfreighter. The Centaurus was also used in the military Hawker Sea Fury, Blackburn Firebrand, Bristol Brigand and the Fairey Spearfish. The poppet valve's previous problems with sealing and wear had been remedied by the use of better materials and the inertia problems with the use of large valves were reduced by using several smaller valves instead, giving increased flow area and reduced mass, and the exhaust valve hot spot by Sodium-cooled valves. Up to that point, the single sleeve valve had won every contest against the poppet valve in comparison of power to displacement. The difficulty of nitride hardening, then finish-grinding the sleeve valve for truing the circularity, may have been a factor in its lack of commercial application.

The Knight-Argyll Patent Case[edit]

When the Argyll car was launched in 1911, the Knight and Kilbourne Company immediately brought a case against Argyll for infringement of their original 1905 patent. This patent described an engine with a single moving sleeve, whereas the Daimler engines being built at the time were based on the 1908 Knight patent which had engines with two moving sleeves. As part of the litigation an engine was built according to the 1905 specification and developed no more than a fraction of the rated RAC horsepower. This fact coupled with other legal and technical arguments[15] led the judge to rule, at the end of July 1912, that the holders of the original Knight patent could not be supported in their claim that it gave them master rights encompassing the Argyll design.

Modern usage[edit]

The sleeve valve has begun to make something of a comeback, due to modern materials, dramatically better engineering tolerances and modern construction techniques, which produce a sleeve valve that leaks very little oil. However, most advanced engine research is concentrated on improving other internal combustion engine designs, such as the Wankel.

Mike Hewland with his assistant John Logan, and also independently Keith Duckworth experimented with a single-cylinder sleeve-valve test engine when looking at Cosworth DFV replacements. Hewland claimed to have obtained 72 hp (54 kW) from a 500 cc single-cylinder engine, with a specific fuel consumption of 177 gr/HP/hr — 0.45 to 0.39 lb/hp/hr-, the engine being able to work on creosote with no specific lubrication supply for the sleeve, just the sleeve driving mechanism requires a specially devoted lubrication, and a lubricating oil use half of the poppet-valve engines of its time. Hewland reported also that the highest temperature measured in the cylinder head didn't exceed 150°C, sleeve temperatures were around 140°C, Temp. was 270°C in the centre of cylinder and 240°C at the edge, and having raced the engine up to the region of 10,000 rpm.

A SAE paper from 2003 deals with a high-speed, small-displacement sleeve-valve engine, calculated, but not experimentally shown, to have a higher SFC than the poppet-valve alternative, a year-2009 work compares two different side-opening intake strategies for sleeve-valve engines.

An unusual form of four-stroke model engine that uses what is essentially a sleeve-valve format, is the British RCV series of "SP" model engines, which use a rotating cylinder liner driven through a bevel gear at the cylinder liner's "bottom" and, even more unusually, have the propeller shaft — as an integrally machined part of the rotating cylinder liner — emerging from what would normally be the cylinder's "top" at the extreme front of the engine, achieving a 2:1 gear reduction ratio compared to the vertically oriented crankshaft's rotational speed. The same firm's "CD" series of model engines use a conventional upright single cylinder with the crankshaft used to spin the propeller directly and also use the rotating cylinder valve. As a parallel with the earlier Charles Knight-designed sleeve-valved automotive powerplants, any RCV sleeve-valved model engine that is run on model glow engine fuel using castor oil as a small percentage (about 2% to 4% content) of the lubricant in the fuel allows the "varnish" created through engine operation to provide a better pneumatic seal between the rotating cylinder valve and the unitized engine cylinder/head castings, initially formed while the engine is being broken in.[16]

Steam engine[edit]

Sleeve valves have occasionally been used on steam engines, for example the SR Leader class.

See also[edit]


  1. ^ Autocar Handbook (Ninth ed. ed.). The Autocar. c. 1919. pp. 36–38. 
  2. ^ Autocar Handbook (Ninth ed. ed.). The Autocar. c. 1919. pp. 37–39. 
  3. ^ "Cuff sleeve valves, description". The Autocar. 19 December 1914. 
  4. ^ W. A. Frederick, SAE Journal, May 1927
  5. ^ George A. Oliver, The Single Sleeve-valve Argylls, Profile Publications Number 67 - Cars -, London 1967
  6. ^ LJK Setright, Some Unusual Engines, London, 1979, p 62
  7. ^ Bentele, Max (1991). Engine Revolutions: The Autobiography of Max Bentele. Warrendale, Pennsylvania: SAE. p. 5. ISBN 978-1-56091-081-7. "During World War II, my original enthusiasm for the sleeve-valve engine simplicity proved to be based on dubious premises. My inspection of a captured Bristol two-row radial engine revealed a bucket full of gear wheels for the sleeve drive. I believe there were over 100 gears!" 
  8. ^ RAC Rating
  9. ^ Petryshyn, Jaroslav (2000). Made Up To A Standard: Thomas Alexander Russell and the Russell Motor Car. General Store Publishing House. pp. 65–66. ISBN 1-894263-25-1. 
  10. ^ Lord Montagu and David Burgess-Wise Daimler Century ; Stephens 1995 ISBN 1-85260-494-8
  11. ^ G.N. Georgano, G.N. (1985). Cars: Early and Vintage, 1886–1930. London: Grange-Universal. 
  12. ^ Hillier, Victor A.W.; F.W. Pittuck (1991). Fundamentals of Motor Vehicle Technology. Nelson Thornes. p. 36. ISBN 0-7487-0531-7. 
  13. ^ Motor Cycle, April 20th, 1922, page iv
  14. ^ "Modern Practice in Engine Design", Motor Cycle, March 16th, 1922, p325
  15. ^ "The Knight-Argll Patent Case", The Automotor Journal, 3rd August, 1912, pp919-920
  16. ^ Keith Lawes. "The Rotating Cylinder Valve 4-stroke Engine (SAE Paper 2002-32-1828)". Retrieved 2012-01-03. 
  • Ricardo, Sir Harry R.; Hempson, J G G (1968). The High-Speed Internal-Combustion Engine (Fifth ed.). London and Glasgow: Blackie & Son. pp. 290–322. 
  • "Sleeve valve engines". Cambridge University Engineering Department. 
  • Aircraft Engine Historical Society -AEHS- publication "Torque Meter", Vol 7, issues 2,3,4.
  • Robert J. Raymond: "Comparison of Sleeve and Poppet-Valve Aircraft Piston Engines", AEHS 2005
  • Car & Driver, July 1974 (Cover showing a Bricklin car): interview with Mike Hewland by Charles Fox
  • J B Hull: "Non-Poppet Valve Motors at the 1911 Olympia Show", SAE paper 120011.
  • Harry Ricardo: "Recent Research Work on the Internal Combustion Engine", SAE Journal, May 1922, pp 305–336 (ends in p. 347)
  • R Abell: "Single Valve Internal Combustion Engine Design and Operation", SAE Journal, Oct 1923, pp 301–309 (Another type of non-poppet valve, used also by Lotus in a 2-stroke engine -SAE paper 920779)
  • P M Heldt: "Sleeve-Valve Engines", SAE Journal, March 1926, pp 303–314
  • W.A. Frederick: "The Single-Sleeve-Valve Engine", SAE Journal, May 1927, pp 661–678 (Calculations).
  • G L Ensor: "Some Notes on the Single-Sleeve Valve", The Institution of Automobile Engineers (London) Proceedings, Vol XXII, Session 1927-28, pp 651–719.
  • A M Niven: "Internal combustion engine", Patent US 1739255, 1929.
  • Frank Jardine: "Thermal Expansion in Automotive Engine Design", SAE Journal, Sept 1930, pp 311–318, and SAE paper 300010.
  • A M Niven: "Sleeve valve actuating mechanism", Patent US 1764972, 1930.
  • A M NIven: "Internal combustion engine", Patent US 1778911, 1930.
  • A M Niven: "Sleeve valve cylinder head", Patent US 1780763, 1930.
  • A M Niven: "Sleeve valve driving mechanism", Patent US 1789341, 1931.
  • A M Niven: "Sleeve valve and method of making same", Patent Nº US1814764A; 1931
  • A M Niven: "Sleeve valve and method of making same", U.S. Patent N º 1,820,629; 1931
  • A. H. R. Fedden: "The Single Sleeve as a Valve Mechanism for the Aircraft Engine", SAE paper 380161.
  • Ashley C Hewitt: "Small High-Speed Single Sleeve Valve Engine", SAE paper 390049 (Single cylinder, air cooled 4.21 ci., 70 cc. engine).
  • W P Ricart: "Some European Comments on High-Output Automobile and Aero-Engines", SAE paper 390099.
  • P V Lamarque, "The design of Cooling Fins for Motor-Cycle Engines", Report of the Automobile Research Committee, Institution of Automobile Engineers Magazine, March 1943 issue, and also in "The Institution of Automobile Engineers Proceedings-London-", Vol. XXXVII, Session 1942-43, pp 99–134 and 309-312.
  • Robert Insley & Arthur W. Green: "Method for making valve sleeves", U.S. Patent Nº 2,319,546; 1943
  • sir Harry Ricardo: "The High-Speed Internal Combustion Engine", London, 1953 Ed. (Materials, see also in talk).
  • William Wagner: "Continental ! its Motors and its People", Aero Publishers, CA, 1983.
  • Strictly I.C. Magazine, Vol 14, Numbers 83 & 84 (Construction of a 1/3 scale model of a Barr & Stroud SSV Motorcycle Engine).
  • Robert J. Raymond: "Comparison of Sleeve and Poppet-Valve Aircraft Piston Engines", AEHS, April 2005. [2]
  • Kimble D. McCutcheon: "The Liquid-Cooled Engines of Pratt & Whitney", AEHS, 2006. [3]
  • Muhammad Hafdiz Rahmat et al. (PETRONAS): "Side Opening Intake Strategy Simulation and Validation of a Sleeve-Valve Port Application", SAE paper 2009-32-0130/20097130
  • Anish Gokhale et al.: "Optimization of Engine Cooling through Conjugate Heat Transfer Simulation and Analysis of Fins", SAE Paper 2012-32-0054
  • YouTube: Videos by ChargerMiles007 and others, search keyword: Sleeve Valve.
  • Anson Engine Museum: YouTube video on The Petter Brotherhood Engine, A railroad Single Sleeve-Valve Engine, designed around 1930 in the company participated by J. B. Mirrlees.
  • Bristol Engines' Manuals [4]

External links[edit]

Original courtesy of Wikipedia: http://en.wikipedia.org/wiki/Sleeve_valve — Please support Wikipedia.
This page uses Creative Commons Licensed content from Wikipedia. A portion of the proceeds from advertising on Digplanet goes to supporting Wikipedia.
156326 videos foundNext > 

1908 Knight Daimler Sleeve Valve Engine Start Up

This very unique sleeve valve engine first built in 1908 was rebuilt extensively by Nimmo Machine in Costa Mesa. It was started for the first time in many ye...

Bristol Hercules sleeve valve radial engine

Bristol Hercules Mk.734 - 2000hp 14 cylinder sleeve valve radial engine. Once fitted to a SAFE Air Bristol Freighter and based in Blenheim, New Zealand. This...

sleeve valve engine ports and sleeve 3of3

sleeve valve engine taken apart #3.

Bristol Hercules sleeve valve radial animation

an animation based on the Bristol engine designed prior to WW2. The four cycle engine used moving sleeves between the piston and cylinder instead of valves. ...

Knight Sleeve Valve Engine

This is a cutaway of a Knight Sleeve Valve engine. This design of engine does not use the traditional poppet type valve found in most other internal combusti...

1923 Daimler Sleeve Valve Landaulet on the road

A ride in a 1923 Daimler D16 landaulet. Sleeve valve engines are very quiet running but burn quite a bit of oil even when they were new. All Daimler engines ...

Willys Knight Sleeve Valve Engine First Run After Overhaul

First run of the Willys Knight sleeve valve engine after a rebuild. This engine last ran in 1960. The ignition timing was too far retarded in this video, so ...

Sleeve Valve Lawnmower Engine Running

A 5 port Sleeve Valve 4 cycle engine made from a Briggs & Stratton 3-1/2 hp lawnmower engine. It has 3 Inlet and 2 Exhaust ports. The sleeve itself only has ...

Brotherhood Sleeve Valve Engine 2nd Run, Part 21

After the excitement of the first run on Friday and to prove to the rest of the team that it wasn't a "Hollywood Stunt" we gave the Brotherhood another run a...

Bristol Hercules Sleeve Valve

A big moment for any restorer of a Bristol Hercules engine - turning her over for the first time on the starter motor. The simplicity of the sleeve valve sys...

156326 videos foundNext > 

2 news items

Western Daily Press

Western Daily Press
Tue, 19 Aug 2014 05:22:30 -0700

Road locomotive Gigantic on its way to the Great Dorset Steam Fair at Blandford. Picture Steve Roberts. The World War One convoy makes its way to the Great Dorset Steam Fair at Blandford. Picture: Steve Roberts. A Pickfords trailer carrying a 1914 Holt ...
Auto Body Professionals Club (subscription)
Tue, 12 Aug 2014 02:33:45 -0700

Instant Access to UK Bodyshop News with your credit card The introduction of new rules forcing manufacturers to install Tyre Pressure Monitoring Systems (TPMS) means workshops should be prepared for an expected increase in demand for repairs, says ...

Oops, we seem to be having trouble contacting Twitter

Talk About Sleeve valve

You can talk about Sleeve valve with people all over the world in our discussions.

Support Wikipedia

A portion of the proceeds from advertising on Digplanet goes to supporting Wikipedia. Please add your support for Wikipedia!