digplanet beta 1: Athena
Share digplanet:


Applied sciences






















Dust blows from the Sahara Desert over the Atlantic Ocean towards the Canary Islands.

Sediment transport is the movement of solid particles (sediment), typically due to a combination of gravity acting on the sediment, and/or the movement of the fluid in which the sediment is entrained. Sediment transport occurs in natural systems where the particles are clastic rocks (sand, gravel, boulders, etc.), mud, or clay; the fluid is air, water, or ice; and the force of gravity acts to move the particles along the sloping surface on which they are resting. Sediment transport due to fluid motion occurs in rivers, oceans, lakes, seas, and other bodies of water due to currents and tides. Transport is also caused by glaciers as they flow, and on terrestrial surfaces under the influence of wind. Sediment transport due only to gravity can occur on sloping surfaces in general, including hillslopes, scarps, cliffs, and the continental shelf—continental slope boundary.

Sediment transport is important in the fields of sedimentary geology, geomorphology, civil engineering and environmental engineering (see applications, below). Knowledge of sediment transport is most often used to determine whether erosion or deposition will occur, the magnitude of this erosion or deposition, and the time and distance over which it will occur.


Sand blowing off a crest in the Kelso Dunes of the Mojave Desert, California.
Toklat River, East Fork, Polychrome overlook, Denali National Park, Alaska. This river, like other braided streams, rapidly changes the positions of its channels through processes of erosion, sediment transport, and deposition.


Main article: Aeolian processes

Aeolian or eolian (depending on the parsing of æ) is the term for sediment transport by wind. This process results in the formation of ripples and sand dunes. Typically, the size of the transported sediment is fine sand (<1 mm) and smaller, because air is a fluid with low density and viscosity, and can therefore not exert very much shear on its bed.

Bedforms are generated by aeolian sediment transport in the terrestrial near-surface environment. Ripples[1] and dunes[2] form as a natural self-organizing response to sediment transport.

Aeolian sediment transport is common on beaches and in the arid regions of the world, because it is in these environments that vegetation does not prevent the presence and motion of fields of sand.

Wind-blown very fine-grained dust is capable of entering the upper atmosphere and moving across the globe. Dust from the Sahara deposits on the Canary Islands and islands in the Caribbean,[3] and dust from the Gobi desert has deposited on the western United States.[4] This sediment is important to the soil budget and ecology of several islands.

Deposits of fine-grained wind-blown glacial sediment are called loess.


In geology, physical geography, and sediment transport, fluvial processes relate to flowing water in natural systems. This encompasses rivers, streams, periglacial flows, flash floods and glacial lake outburst floods. Sediment moved by water can be larger than sediment moved by air because water has both a higher density and viscosity. In typical rivers the largest carried sediment is of sand and gravel size, but larger floods can carry cobbles and even boulders.

Fluvial sediment transport can result in the formation of ripples and dunes, in fractal-shaped patterns of erosion, in complex patterns of natural river systems, and in the development of floodplains.

Sand ripples, Laysan Beach, Hawaii. Coastal sediment transport results in these evenly spaced ripples along the shore. Monk seal for scale.


Coastal sediment transport takes place in near-shore environments due to the motions of waves and currents. At the mouths of rivers, coastal sediment and fluvial sediment transport processes mesh to create river deltas.

Coastal sediment transport results in the formation of characteristic coastal landforms such as beaches, barrier islands, and capes.[5]

A glacier joining the Gorner Glacier, Zermatt, Switzerland. These glaciers transport sediment and leave behind lateral moraines.


As glaciers move over their beds, they entrain and move material of all sizes. Glaciers can carry the largest sediment, and areas of glacial deposition often contain a large number of glacial erratics, many of which are several metres in diameter. Glaciers also pulverize rock into "glacial flour", which is so fine that it is often carried away by winds to create loess deposits thousands of kilometres afield. Sediment entrained in glaciers often moves approximately along the glacial flowlines, causing it to appear at the surface in the ablation zone.


In hillslope sediment transport, a variety of processes move regolith downslope. These include:

  • Soil creep
  • Tree throw
  • Movement of soil by burrowing animals
  • Slumping and landsliding of the hillslope

These processes generally combine to give the hillslope a profile that looks like a solution to the diffusion equation, where the diffusivity is a parameter that relates to the ease of sediment transport on the particular hillslope. For this reason, the tops of hills generally have a parabolic concave-up profile, which grades into a convex-up profile around valleys.

As hillslopes steepen, however, they become more prone to episodic landslides and other mass wasting events. Therefore, hillslope processes are better described by a nonlinear diffusion equation in which classic diffusion dominates for shallow slopes and erosion rates go to infinity as the hillslope reaches a critical angle of repose.[6]

Debris flow[edit]

Large masses of material are moved in debris flows, hyperconcentrated mixtures of mud, clasts that range up to boulder-size, and water. Debris flows move as granular flows down steep mountain valleys and washes. Because they transport sediment as a granular mixture, their transport mechanisms and capacities scale differently from those of fluvial systems.


Suspended sediment from a stream emptying into a fjord (Isfjorden, Svalbard, Norway).

Sediment transport is applied to solve many environmental, geotechnical, and geological problems. Measuring or quantifying sediment transport or erosion is therefore important for coastal engineering. Several sediment erosion devices have been designed in order to quantitfy sediment erosion (e.g., Particle Erosion Simulator (PES)). One such device, also referred to as the BEAST (Benthic Environmental Assessment Sediment Tool) has been calibrated in order to quantify rates of sediment erosion.[7]

Movement of sediment is important in providing habitat for fish and other organisms in rivers. Therefore, managers of highly regulated rivers, which are often sediment-starved due to dams, are often advised to stage short floods to refresh the bed material and rebuild bars. This is also important, for example, in the Grand Canyon of the Colorado River, to rebuild shoreline habitats also used as campsites.

Sediment discharge into a reservoir formed by a dam forms a reservoir delta. This delta will fill the basin, and eventually, either the reservoir will need to be dredged or the dam will need to be removed. Knowledge of sediment transport can be used to properly plan to extend the life of a dam.

Geologists can use inverse solutions of transport relationships to understand flow depth, velocity, and direction, from sedimentary rocks and young deposits of alluvial materials.

Flow in culverts, over dams, and around bridge piers can cause erosion of the bed. This erosion can damage the environment and expose or unsettle the foundations of the structure. Therefore, good knowledge of the mechanics of sediment transport in a built environment are important for civil and hydraulic engineers.

When suspended sediment transport is increased due to human activities, causing environmental problems including the filling of channels, it is called siltation after the grain-size fraction dominating the process.

Initiation of motion[edit]

Stress balance[edit]

For a fluid to begin transporting sediment that is currently at rest on a surface, the boundary (or bed) shear stress \tau_b exerted by the fluid must exceed the critical shear stress \tau_c for the initiation motion of grains at the bed. This basic criterion for the initiation of motion can be written as:


This is typically represented by a comparison between a dimensionless shear stress (\tau_b*)and a dimensionless critical shear stress (\tau_c*). The nondimensionalization is in order to compare the driving forces of particle motion (shear stress) to the resisting forces that would make it stationary (particle density and size). This dimensionless shear stress, \tau*, is called the Shields parameter and is defined as:


And the new equation to solve becomes:


The equations included here describe sediment transport for clastic, or granular sediment. They do not work for clays and muds because these types of floccular sediments do not fit the geometric simplifications in these equations, and also interact thorough electrostatic forces. The equations were also designed for fluvial sediment transport of particles carried along in a liquid flow, such as that in a river, canal, or other open channel.

Only one size of particle is considered in this equation. However, river beds are often formed by a mixture of sediment of various sizes. In case of partial motion where only a part of the sediment mixture moves, the river bed becomes enriched in large gravel as the smaller sediments are washed away. The smaller sediments present under this layer of large gravel have a lower possibility of movement and total sediment transport decreases. This is called armouring effect.[8] Other forms of armouring of sediment or decreasing rates of sediment erosion can be caused by carpets of microbial mats, under conditions of high organic loading.[9]

Critical shear stress[edit]

The Shields diagram empirically shows how the dimensionless critical shear stress required for the initiation of motion is a function of a particular form of the particle Reynolds number, \mathrm{Re}_p or Reynolds number related to the particle. This allows us to rewrite the criterion for the initiation of motion in terms of only needing to solve for a specific version of the particle Reynolds number, which we call \mathrm{Re}_p*.


This equation can then be solved by using the empirically derived Shields curve to find \tau_c* as a function of a specific form of the particle Reynolds number called the boundary Reynolds number. The mathematical solution of the equation was given by Dey.[10]

Particle Reynolds Number[edit]

In general, a particle Reynolds Number has the form:

\mathrm{Re}_p=\frac{U_p D}{\nu}

Where U_p is a characteristic particle velocity, D is the grain diameter (a characteristic particle size), and \nu is the kinematic viscosity, which is given by the dynamic viscosity, \mu, divided by the fluid density, \rho.


The specific particle Reynolds number of interest is called the boundary Reynolds number, and it is formed by replacing the velocity term in the Particle Reynolds number by the shear velocity, u_*, which is a way of rewriting shear stress in terms of velocity.

u_*=\sqrt{\frac{\tau_b}{\rho_w}}=\kappa z \frac{\partial u}{\partial z}

where \tau_b is the bed shear stress (described below), and  \kappa is the von Kármán constant, where

 \kappa = {0.407}.

The particle Reynolds number is therefore given by:

\mathrm{Re}_p*=\frac{u_* D}{\nu}

Bed shear stress[edit]

The boundary Reynolds number can be used with the Shields diagram to empirically solve the equation


which solves the right-hand side of the equation


In order to solve the left-hand side, expanded as


we must find the bed shear stress, {\tau_b}. There are several ways to solve for the bed shear stress. First, we develop the simplest approach, in which the flow is assumed to be steady and uniform and reach-averaged depth and slope are used. Due to the difficulty of measuring shear stress in situ, this method is also one of the most-commonly used. This method is known as the depth-slope product.

Depth-slope product[edit]

Main article: Depth-slope product

For a river undergoing approximately steady, uniform equilibrium flow, of approximately constant depth h and slope θ over the reach of interest, and whose width is much greater than its depth, the bed shear stress is given by some momentum considerations stating that the gravity force component in the flow direction equals exactly the friction force.[11] For a wide channel, it yields:

\tau_b=\rho g h \sin(\theta)

For shallow slopes, which are found in almost all natural lowland streams, the small-angle formula shows that \sin(\theta) is approximately equal to \tan(\theta), which is given by S, the slope. Rewritten with this:

\tau_b=\rho g h S

Shear velocity, velocity, and friction factor[edit]

For the steady case, by extrapolating the depth-slope product and the equation for shear velocity:

\tau_b=\rho g h S

We can see that the depth-slope product can be rewritten as:

\tau_b=\rho u_*^2.

u* is related to the mean flow velocity, \bar{u}, through the generalized Darcy-Weisbach friction factor, C_f, which is equal to the Darcy-Weisbach friction factor divided by 8 (for mathematical convenience).[12] Inserting this friction factor,

\tau_b=\rho C_f \left(\bar{u} \right)^2.

Unsteady flow[edit]

For all flows that cannot be simplified as a single-slope infinite channel (as in the depth-slope product, above), the bed shear stress can be locally found by applying the Saint-Vennant equations for continuity, which consider accelerations within the flow.



The criterion for the initiation of motion, established earlier, states that


In this equation,

\tau*=\frac{\tau_b}{(\rho_s-\rho)(g)(D)}, and therefore
\tau_c* is a function of boundary Reynolds number, a specific type of particle Reynolds number.
\tau_c*=f \left(Re_p* \right).

For a particular particle Reynolds number, \tau_c* will be an emprical constant given by the Shields Curve or by another set of empirical data (depending on whether or not the grain size is uniform).

Therefore, the final equation that we seek to solve is:

\frac{\tau_b}{(\rho_s-\rho)(g)(D)}=f \left(Re_p* \right).


We make several assumptions to provide an example that will allow us to bring the above form of the equation into a solved form.

First, we assume that the a good approximation of reach-averaged shear stress is given by the depth-slope product. We can then rewrite the equation as

{\rho g h S}=0.06{(\rho_s-\rho)(g)(D)}.

Moving and re-combining the terms, we obtain:

{h S}={\frac{(\rho_s-\rho)}{\rho}(D)}\left(f \left(\mathrm{Re}_p* \right) \right)=R D \left(f \left(\mathrm{Re}_p* \right) \right)

where R is the submerged specific gravity of the sediment.

We then make our second assumption, which is that the particle Reynolds number is high. This is typically applicable to particles of gravel-size or larger in a stream, and means that the critical shear stress is a constant. The Shields curve shows that for a bed with a uniform grain size,


Later researchers[citation needed] have shown that this value is closer to


for more uniformly sorted beds. Therefore, we will simply insert

\tau_c*=f \left(\mathrm{Re}_p* \right)

and insert both values at the end.

The equation now reads:

{h S}=R D \tau_c*

This final expression shows that the product of the channel depth and slope is equal to the Shield's criterion times the submerged specific gravity of the particles times the particle diameter.

For a typical situation, such as quartz-rich sediment \left(\rho_s=2650 \frac{kg}{m^3} \right) in water \left(\rho=1000 \frac{kg}{m^3} \right), the submerged specific gravity is equal to 1.65.


Plugging this into the equation above,

{h S}=1.65(D)\tau_c*.

For the Shield's criterion of \tau_c*=0.06. 0.06 * 1.65 = 0.099, which is well within standard margins of error of 0.1. Therefore, for a uniform bed,

{h S}={0.1(D)}.

For these situations, the product of the depth and slope of the flow should be 10% of the diameter of the median grain diameter.

The mixed-grain-size bed value is \tau_c*=0.03, which is supported by more recent research as being more broadly applicable because most natural streams have mixed grain sizes. Using this value, and changing D to D_50 ("50" for the 50th percentile, or the median grain size, as we are now looking at a mixed-grain-size bed), the equation becomes:

{h S}={0.05(D_{50})}

Which means that the depth times the slope should be about 5% of the median grain diameter in the case of a mixed-grain-size bed.

Modes of entrainment[edit]

The sediments entrained in a flow can be transported along the bed as bed load in the form of sliding and rolling grains, or in suspension as suspended load advected by the main flow.[11] Some sediment materials may also come from the upstream reaches and be carried downstream in the form of wash load.

Rouse number[edit]

The location in the flow in which a particle is entrained is determined by the Rouse number, which is determined by the density ρs and diameter d of the sediment particle, and the density ρ and kinematic viscosity ν of the fluid, determine in which part of the flow the sediment particle will be carried.[13]

P=\frac{w_s}{\kappa u_\ast}

Here, the Rouse number is given by P. The term in the numerator is the (downwards) sediment the sediment settling velocity ws, which is discussed below. The upwards velocity on the grain is given as a product of the von Kármán constant, κ = 0.4, and the shear velocity, u.

The following table gives the approximate required Rouse numbers for transport as bed load, suspended load, and wash load.[13][14]

Mode of Transport Rouse Number
Initiation of motion >7.5
Bed load >2.5, <7.5
Suspended load: 50% Suspended >1.2, <2.5
Suspended load: 100% Suspended >0.8, <1.2
Wash load <0.8

Settling velocity[edit]

Streamlines around a sphere falling through a fluid. This illustration is accurate for laminar flow, in which the particle Reynolds number is small. This is typical for small particles falling through a viscous fluid; larger particles would result in the creation of a turbulent wake.

The settling velocity (also called the "fall velocity" or "terminal velocity") is a function of the particle Reynolds number. Generally, for small particles (laminar approximation), it can be calculated with Stokes' Law. For larger particles (turbulent particle Reynolds numbers), fall velocity is calculated with the turbulent drag law. Dietrich (1982) compiled a large amount of published data to which he empirically fit settling velocity curves.[15] Ferguson and Church (2006) analytically combined the expressions for Stokes flow and a turbulent drag law into a single equation that works for all sizes of sediment, and successfully tested it against the data of Dietrich.[16] Their equation is

w_s=\frac{RgD^2}{C_1 \nu + (0.75 C_2 R g D^3)^{(0.5)}}.

In this equation ws is the sediment settling velocity, g is acceleration due to gravity, and D is mean sediment diameter. \nu is the kinematic viscosity of water, which is approximately 1.0 x 10−6 m2/s for water at 20 °C.

C_1 and C_2 are constants related to the shape and smoothness of the grains.

Constant Smooth Spheres Natural Grains: Sieve Diameters Natural Grains: Nominal Diameters Limit for Ultra-Angular Grains
C_1 18 18 20 24
C_2 0.4 1.0 1.1 1.2

The expression for fall velocity can be simplified so that it can be solved only in terms of D. We use the sieve diameters for natural grains, g=9.8, and values given above for \nu and R. From these parameters, the fall velocity is given by the expression:

w_s=\frac{16.17D^2}{1.8\cdot10^{-5} + (12.1275D^3)^{(0.5)}}

Hjulström-Sundborg Diagram[edit]

The logarithmic Hjulström curve

In 1935, Filip Hjulström created the Hjulström curve, a graph which shows the relationship between the size of sediment and the velocity required to erode (lift it), transport it, or deposit it.[17] The graph is logarithmic.

Åke Sundborg later modified the Hjulström curve to show separate curves for the movement threshold corresponding to several water depths, as is necessary if the flow velocity rather than the boundary shear stress (as in the Shields diagram) is used for the flow strength.[18]

Transport rate[edit]

A schematic diagram of where the different types of sediment load are carried in the flow. Dissolved load is not sediment: it is composed of disassociated ions moving along with the flow. It may, however, constitute a significant proportion (often several percent, but occasionally greater than half) of the total amount of material being transported by the stream.

Formulas to calculate sediment transport rate exist for sediment moving in several different parts of the flow. These formulas are often segregated into bed load, suspended load, and wash load. They may sometimes also be segregated into bed material load and wash load.

Bed Load[edit]

Bed load moves by rolling, sliding, and hopping (or saltating) over the bed, and moves at a small fraction of the fluid flow velocity. Bed load is generally thought to constitute 5-10% of the total sediment load in a stream, making it less important in terms of mass balance. However, the bed material load (the bed load plus the portion of the suspended load which comprises material derived from the bed) is often dominated by bed load, especially in gravel-bed rivers. This bed material load is the only part of the sediment load that actively interacts with the bed. As the bed load is an important component of that, it plays a major role in controlling the morphology of the channel.

Bed load transport rates are usually expressed as being related to excess dimensionless shear stress raised to some power. Excess dimensionless shear stress is a nondimensional measure of bed shear stress about the threshold for motion.


Bed load transport rates may also be given by a ratio of bed shear stress to critical shear stress, which is equivalent in both the dimensional and nondimensional cases. This ratio is called the "transport stage" (T_s \text{ or } \phi) and is an important in that it shows bed shear stress as a multiple of the value of the criterion for the initiation of motion.


When used for sediment transport formulae, this ratio is typically raised to a power.

The majority of the published relations for bedload transport are given in dry sediment weight per unit channel width, b ("breadth"):


Due to the difficulty of estimating bed load transport rates, these equations are typically only suitable for the situations for which they were designed.

Notable bed load transport formulae[edit]

Meyer-Peter Müller and derivatives[edit]

The transport formula of Meyer-Peter and Müller, originally developed in 1948,[19] was designed for well-sorted fine gravel at a transport stage of about 8.[13] The formula uses the above nondimensionalization for shear stress,[13]


and Hans Einstein's nondimensionalization for sediment volumetric discharge per unit width[13]

q_s* = \frac{q_s}{D \sqrt{\frac{\rho_s-\rho}{\rho} g D}} = \frac{q_s}{Re_p \nu}.

Their formula reads:

q_s* = 8\left(\tau*-\tau*_c \right)^{3/2}.[13]

Their experimentally determined value for \tau*_c is 0.047, and is the third commonly used value for this (in addition to Parker's 0.03 and Shields' 0.06).

Because of its broad use, some revisions to the formula have taken place over the years that show that the coefficient on the left ("8" above) is a function of the transport stage:[13][20][21][22]

T_s \approx 2 \rightarrow q_s* = 5.7\left(\tau*-0.047 \right)^{3/2}[20]
T_s \approx 100 \rightarrow q_s* = 12.1\left(\tau*-0.047 \right)^{3/2}[21][22]

The variations in the coefficient were later generalized as a function of dimensionless shear stress:[13][23]

\begin{cases} q_s* = \alpha_s \left(\tau*-\tau_c* \right)^n \\ n = \frac{3}{2} \\ \alpha_s = 1.6 \ln\left(\tau*\right) + 9.8 \approx 9.64 \tau*^{0.166} \end{cases}[23]
Wilcock and Crowe[edit]

In 2003, Peter Wilcock and Joanna Crowe (now Joanna Curran) published a sediment transport formula that works with multiple grain sizes across the sand and gravel range.[24] Their formula works with surface grain size distributions, as opposed to older models which use subsurface grain size distributions (and thereby implicitly infer a surface grain sorting).

Their expression is more complicated than the basic sediment transport rules (such as that of Meyer-Peter and Müller) because it takes into account multiple grain sizes: this requires consideration of reference shear stresses for each grain size, the fraction of the total sediment supply that falls into each grain size class, and a "hiding function".

The "hiding function" takes into account the fact that, while small grains are inherently more mobile than large grains, on a mixed-grain-size bed, they may be trapped in deep pockets between large grains. Likewise, a large grain on a bed of small particles will be stuck in a much smaller pocket than if it were on a bed of grains of the same size. In gravel-bed rivers, this can cause "equal mobility", in which small grains can move just as easily as large ones.[25] As sand is added to the system, it moves away from the "equal mobility" portion of the hiding function to one in which grain size again matters.[24]

Their model is based on the transport stage, or ratio of bed shear stress to critical shear stress for the initiation of grain motion. Because their formula works with several grain sizes simultaneously, they define the critical shear stress for each grain size class, \tau_{c,D_i}, to be equal to a "reference shear stress", \tau_{ri}.[24]

They express their equations in terms of a dimensionless transport parameter, W_i^* (with the "*" indicating nondimensionality and the "_i" indicating that it is a function of grain size):

W_i^* = \frac{R g q_{bi}}{F_i u*^3}

q_{bi} is the volumetric bed load transport rate of size class i per unit channel width b. F_i is the proportion of size class i that is present on the bed.

They came up with two equations, depending on the transport stage, \phi. For \phi < 1.35:

W_i^* = 0.002 \phi^{7.5}

and for \phi \geq 1.35:

W_i^* = 14 \left(1 - \frac{0.894}{\phi^{0.5}}\right)^{4.5}.

This equation asymptotically reaches a constant value of W_i^* as \phi becomes large.

Suspended load[edit]

Suspended load is carried in the lower to middle parts of the flow, and moves at a large fraction of the mean flow velocity in the stream.

A common characterization of suspended sediment concentration in a flow is given by the Rouse Profile. This characterization works for the situation in which sediment concentration c_0 at one particular elevation above the bed z_0 can be quantified. It is given by the expression:

\frac{c_s}{c_0} = \left[\frac{z \left(h-z_0\right)}{z_0\left(h-z\right)}\right]^{-P/\alpha}

Here, z is the elevation above the bed, c_s is the concentration of suspended sediment at that elevation, h is the flow depth, P is the Rouse number, and \alpha relates the eddy viscosity for momentum K_m to the eddy diffusivity for sediment, which is approximately equal to one.[26]

\alpha = \frac{K_s}{K_m} \approx 1

Experimental work has shown that \alpha ranges from 0.93 to 1.10 for sands and silts.[27]

The Rouse profile characterizes sediment concentrations because the Rouse number includes both turbulent mixing and settling under the weight of the particles. Turbulent mixing results in the net motion of particles from regions of high concentrations to low concentrations. Because particles settle downward, for all cases where the particles are not neutrally buoyant or sufficiently light that this settling velocity is negligible, there is a net negative concentration gradient as one goes upward in the flow. The Rouse Profile therefore gives the concentration profile that provides a balance between turbulent mixing (net upwards) of sediment and the downwards settling velocity of each particle.

Bed material load[edit]

Bed material load comprises the bed load and the portion of the suspended load that is sourced from the bed.

Three common bed material transport relations are the "Ackers-White",[28] "Engelund-Hansen", "Yang" formulae. The first is for sand to granule-size gravel, and the second and third are for sand[29] though Yang later expanded his formula to include fine gravel. That all of these formulae cover the sand-size range and two of them are exclusively for sand is that the sediment in sand-bed rivers is commonly moved simultaneously as bed and suspended load.


The bed material load formula of Engelund and Hansen is the only one to not include some kind of critical value for the initiation of sediment transport. It reads:

q_s* = \frac{0.05}{c_f} \tau*^{2.5}

where q_s* is the Einstein nondimensionalization for bed shear stress, c_f is a friction factor, and \tau* is the Shields stress. The Engelund-Hansen formula is one of the few sediment transport formulae in which a threshold "critical shear stress" is absent.

Wash load[edit]

Wash load is carried within the water column as part of the flow, and therefore moves with the mean velocity of main stream. Wash load concentrations are approximately uniform in the water column. This is described by the endmember case in which the Rouse number is equal to 0 (i.e. the settling velocity is far less than the turbulent mixing velocity), which leads to a prediction of a perfectly uniform vertical concentration profile of material.

Total load[edit]

Some authors have attempted formulations for the total sediment load carried in water.[30][31] These formulas are designed largely for sand, as (depending on flow conditions) sand often can be carried as both bed load and suspended load in the same stream or shoreface.

See also[edit]


  1. ^ Anderson, R (1990). "Eolian ripples as examples of self-organization in geomorphological systems". Earth-Science Reviews 29: 77. doi:10.1016/0012-8252(0)90029-U. 
  2. ^ Kocurek, Gary; Ewing, Ryan C. (2005). "Aeolian dune field self-organization – implications for the formation of simple versus complex dune-field patterns". Geomorphology 72: 94. Bibcode:2005Geomo..72...94K. doi:10.1016/j.geomorph.2005.05.005. 
  3. ^ Goudie, A; Middleton, N.J. (2001). "Saharan dust storms: nature and consequences". Earth-Science Reviews 56: 179. Bibcode:2001ESRv...56..179G. doi:10.1016/S0012-8252(01)00067-8. 
  4. ^ http://earthobservatory.nasa.gov/IOTD/view.php?id=6458
  5. ^ Ashton, Andrew; Murray, A. Brad; Arnault, Olivier (2001). "Formation of coastline features by large-scale instabilities induced by high-angle waves". Nature 414 (6861): 296–300. Bibcode:2001Natur.414..296A. doi:10.1038/35104541. PMID 11713526. 
  6. ^ Roering, Joshua J.; Kirchner, James W.; Dietrich, William E. (1999). "Evidence for nonlinear, diffusive sediment transport on hillslopes and implications for landscape morphology". Water Resources Research 35 (3): 853. Bibcode:1999WRR....35..853R. doi:10.1029/1998WR900090. 
  7. ^ Grant, J., Walker, T.R., Hill P.S., Lintern, D.G. (2013) BEAST-A portable device for quantification of erosion in intact sediment cores. Methods in Oceanography. DOI: 10.1016/j.mio.2013.03.001
  8. ^ Saniya Sharmeen and Garry R. Willgoose1, The interaction between armouring and particle weathering for eroding landscapes, Earth surface Processes and Landforms 31, 1195–1210 (2006)
  9. ^ Walker, T.R., Grant, J. (2009) Quantifying erosion rates and stability of bottom sediments at mussel aquaculture sites in Prince Edward Island, Canada. Journal of Marine Systems. 75: 46-55. doi:10.1016/j.jmarsys.2008.07.009
  10. ^ Dey S. (1999) Sediment threshold. Applied Mathematical Modelling, Elsevier, Vol. 23, No. 5, 399-417.
  11. ^ a b Hubert Chanson (2004). The Hydraulics of Open Channel Flow: An Introduction. Butterworth-Heinemann, 2nd edition, Oxford, UK, 630 pages. ISBN 978-0-7506-5978-9. 
  12. ^ Whipple, Kelin (2004). "Hydraulic Roughness". 12.163: Surface processes and landscape evolution. MIT OCW. Retrieved 2009-03-27. 
  13. ^ a b c d e f g h Whipple, Kelin (September 2004). "IV. Essentials of Sediment Transport". 12.163/12.463 Surface Processes and Landscape Evolution: Course Notes. MIT OpenCourseWare. Retrieved 2009-10-11. 
  14. ^ Moore, Andrew. "Lecture 20—Some Loose Ends". Lecture Notes: Fluvial Sediment Transport. Kent State. Retrieved 23 December 2009. 
  15. ^ Dietrich, W. E. (1982). "Settling Velocity of Natural Particles". Water Resources Research 18 (6): 1615–1626. Bibcode:1982WRR....18.1615D. doi:10.1029/WR018i006p01615. 
  16. ^ Ferguson, R. I., and M. Church (2006), A Simple Universal Equation for Grain Settling Velocity, Journal of Sedimentary Research, 74(6) 933-937, doi:10.1306/051204740933
  17. ^ The long profile – changing processes: types of erosion, transportation and deposition, types of load; the Hjulstrom curve. coolgeography.co.uk. Last accessed 26 Dec 2011.
  18. ^ Special Topics: An Introduction to Fluid Motions, Sediment Transport, and Current-generated Sedimentary Structures; As taught in: Fall 2006. Massachusetts Institute of Technology. 2006. Last accessed 26 Dec 2011.
  19. ^ Meyer-Peter, E; Müller, R. (1948). Formulas for bed-load transport. Proceedings of the 2nd Meeting of the International Association for Hydraulic Structures Research. pp. 39–64. 
  20. ^ a b Fernandez-Luque, R; van Beek, R (1976). "Erosion and transport of bedload sediment". Jour. Hyd. Research 14 (2). 
  21. ^ a b Cheng, Nian-Sheng (2002). "Exponential Formula for Bedload Transport". Journal of Hydraulic Engineering 128 (10): 942. doi:10.1061/(ASCE)0733-9429(2002)128:10(942). 
  22. ^ a b Wilson, K. C. (1966). "Bed-load transport at high shear stress". J. Hydraul. Div. (ASCE) 92 (6): 49–59. 
  23. ^ a b Wiberg, Patricia L.; Dungan Smith, J. (1989). "Model for Calculating Bed Load Transport of Sediment". Journal of Hydraulic Engineering 115: 101. doi:10.1061/(ASCE)0733-9429(1989)115:1(101). 
  24. ^ a b c Wilcock, Peter R.; Crowe, Joanna C. (2003). "Surface-based Transport Model for Mixed-Size Sediment". Journal of Hydraulic Engineering 129 (2): 120. doi:10.1061/(ASCE)0733-9429(2003)129:2(120). 
  25. ^ Parker, G.; Klingeman, P. C.; McLean, D. G. (1982). "Bedload and Size Distribution in Paved Gravel-Bed Streams". Journal of the Hydraulics Division (ASCE) 108 (4): 544–571. 
  26. ^ Harris, Courtney K. (March 18, 2003). "Lecture 9: Suspended Sediment Transport II". Sediment transport processes in coastal environments. Virginia Institute of Marine Science. Retrieved 23 December 2009. 
  27. ^ Moore, Andrew. "Lecture 21—Suspended Sediment Transport". Lecture Notes: Fluvial Sediment Transport. Kent State. Retrieved 25 December 2009. 
  28. ^ Ackers, P.; White, W.R. (1973). "Sediment Transport: New Approach and Analysis". Journal of the Hydraulics Division (ASCE) 99 (11): 2041–2060. 
  29. ^ Ariffin, J.; A.A. Ghani, N.A. Zakaira, and A.H. Yahya (14–16 October 2002). "Evaluation of equations on total bed material load". International Conference on Urban Hydrology for the 21st Century (Kuala Lumpur). 
  30. ^ Yang, C (1979). "Unit stream power equations for total load". Journal of Hydrology 40: 123. Bibcode:1979JHyd...40..123Y. doi:10.1016/0022-1694(79)90092-1. 
  31. ^ Bailard, James A. (1981). "An Energetics Total Load Sediment Transport Model For a Plane Sloping Beach". Journal of Geophysical Research 86: 10938. Bibcode:1981JGR....8610938B. doi:10.1029/JC086iC11p10938. 

External links[edit]

Original courtesy of Wikipedia: http://en.wikipedia.org/wiki/Sediment_transport — Please support Wikipedia.
This page uses Creative Commons Licensed content from Wikipedia. A portion of the proceeds from advertising on Digplanet goes to supporting Wikipedia.
52434 videos foundNext > 

Suspension and Bedload Sediment Transport

In this video, I describe three basic ways sediment is transported: in suspension, via saltation, and in traction. Saltating and rolling grains (in traction)...

Lecture - 14 Sediment Transport and Deposition

Lecture Series on Engineering Geology by Prof. Debasis Roy, Department of Civil Engineering, I.I.T.,Kharagpur. For more details on NPTEL visit http://nptel.i...

Hydraulic jump, low head dam installation, and coarse sediment transport

River Geomorphology Video created by Little River Research and Design, with funding from the Missouri Department of Natural Resources. http://serc.carleton.e...

Sediment Transport

Underwater video of sediment transport in Akutan, Alaska by High Tide Exploration

This video was taken without the ROV while using only the GoPro HD Hero2. The video was taken on what is locally referred to as South Creek at the head of Ak...

Sediment Transport, 100 g/m/s (7 mm & 1.2 mm)

Filmed and edited by: John Gaffney Location: University of Minnesota's St. Anthony Falls Lab Research supported by: The University of Minnesota's Department ...

Cross Shore Sediment Transport Time Lapse


More floods - more sediment transport - less fish?

A project of the National Research Programme "Sustainable water management" (NRP 61). Dr. Dieter Rickenmann presents the research work carried out in the sco...

Sediment Transport

Sediment is transported as bedload by rolling and saltating. In this video, I review the connections between the boundary layer and sediment transport, inclu...

Sediment Transport, 50 g/m/s (12 mm), Detail

Filmed and edited by: John Gaffney Location: University of Minnesota's St. Anthony Falls Lab Research supported by: The University of Minnesota's Department ...

52434 videos foundNext > 

18 news items

Sun, 06 Jul 2014 22:15:00 -0700

Figure 1 shows an example of suspended sediment transport during three summer days. In addition to SSCs determined by various methods, the figure also shows three of the reference SSCs from laboratory analysis of bottled samples and the time series of ...
Dredging Today
Wed, 30 Jul 2014 06:30:00 -0700

Research funded under this agreement will help ensure that activities, including offshore dredging and beach nourishment, are conducted in a sustainable manner that is compatible with natural sediment transport and biological processes, as well as ...


Tue, 29 Jul 2014 07:43:15 -0700

... had “a number of issues” about the proposal by Tidal Lagoon Swansea Bay PLC including disagreeing with the applicant's mathematical modelling of the environmental impacts of the scheme particularly in relation to its effect on sediment transport.

Southwales Evening Post

Southwales Evening Post
Tue, 29 Jul 2014 05:37:35 -0700

Concerns about the way Swansea Bay Tidal Lagoon Ltd has modelled the effect on sediment transport, and its bid to acquire land, were raised by Christian Silk, of legal firm Eversheds, which is representing Swansea University and Bay Campus landowner ...
Mon, 21 Jul 2014 05:22:30 -0700

Assessing trends in nitrogen (N) loss is much trickier than exploring how erosion and sediment transport in Iowa have been affected by changing precipitation regimes and extreme events. This article looks at studies of the Raccoon River Watershed in Iowa.
Dredging Today
Thu, 24 Jul 2014 23:11:15 -0700

Research funded under this agreement will help ensure that activities including offshore dredging and beach nourishment are conducted in a sustainable manner that is compatible with natural sediment transport and biological processes, as well as ...
The Daily Telegraph
Tue, 08 Jul 2014 23:00:00 -0700

The council said the work would help it improve its knowledge of sediment transport and deposit, and how it can better manage the impacts of development. It also plans to install sediment markers in the lagoon for monitoring. The other part of the ...
Dredging Today
Sun, 20 Jul 2014 23:00:00 -0700

... Big Sarasota Pass (BSP) for use on Lido Key using the Inlet Management Program alternatives would significantly alter the ebb shoal morphology or local/regional sediment transport patterns in a way that would cause adverse impacts to adjacent beaches.

Oops, we seem to be having trouble contacting Twitter

Talk About Sediment transport

You can talk about Sediment transport with people all over the world in our discussions.

Support Wikipedia

A portion of the proceeds from advertising on Digplanet goes to supporting Wikipedia. Please add your support for Wikipedia!