digplanet beta 1: Athena
Share digplanet:

Agriculture

Applied sciences

Arts

Belief

Business

Chronology

Culture

Education

Environment

Geography

Health

History

Humanities

Language

Law

Life

Mathematics

Nature

People

Politics

Science

Society

Technology

Basic parts of an outboard motor

An outboard motor is a propulsion system for boats, consisting of a self-contained unit that includes engine, gearbox and propeller or jet drive, designed to be affixed to the outside of the transom. They are the most common motorized method of propelling small watercraft. As well as providing propulsion, outboards provide steering control, as they are designed to pivot over their mountings and thus control the direction of thrust. The skeg also acts as a rudder when the engine is not running. Unlike inboard motors, outboard motors can be easily removed for storage or repairs.

Bolinder's two-cylinder Trim outboard engine.
A Mercury Marine 50 hp outboard engine, circa 1970s
1979 Evinrude 70 hp outboard, cowling and air silencer removed, exposing its shift/throttle/spark advance linkages, flywheel, and three carburetors

In order to eliminate the chances of hitting bottom with an outboard motor, the motor can be tilted up to an elevated position either electronically or manually. This helps when traveling through shallow waters where there may be debris that could potentially damage the motor as well as the propeller. If the electronic motor required to move the pistons which raise or lower the engine is malfunctioning, every outboard motor is equipped with a manual piston release which will allow the operator to drop the motor down to its lowest setting.[1]

General uses[edit]

Rotor of the impeller pump (cooling system) of an outboard motor
A motorboat with an outboard motor attached to it

Large Outboards[edit]

Large outboards are usually bolted to the transom (or to a bracket bolted to the transom), and are linked to controls at the helm. These range from 2-, 3- and 4-cylinder models generating 15 to 135 horsepower suitable for hulls up to 17 feet (5.2 m) in length, to powerful V6 and V8 cylinder blocks rated up to 557 hp (415 kW).,[2] with sufficient power to be used on boats of 37 feet (11 m) or longer.

Portable[edit]

Small outboard motors, up to 15 horsepower or so are easily portable. They are affixed to the boat via clamps, and thus easily moved from boat to boat. These motors typically use a manual pullcord start system, with throttle and gearshift controls mounted on the body of the motor, and a tiller for steering. The smallest of these weigh as little as 12 kilograms (26 lb), have integral fuel tanks, and provide sufficient power to move a small dinghy at around 8 knots (15 km/h; 9.2 mph) This type of motor is typically used:

  • to power small craft such as jon boats, dinghies, canoes, etc.
  • to provide auxiliary power for sailboats,
  • for trolling aboard larger craft, as small outboards are typically more efficient at trolling speeds. In this application, the motor is frequently installed on the transom alongside and connected to the primary outboard to enable helm steering.

Electric-powered[edit]

Commonly referred to as "trolling motors" or "electric outboard motors", electric outboards are used

  • on very small craft or on small lakes where gasoline motors are prohibited,
  • as a secondary means of propulsion on larger craft, and
  • as repositioning thrusters while fishing for bass and other freshwater species,

and any other application where their quietness, and ease of operation and zero emissions outweigh the speed and range deficiencies.

Pump-jet[edit]

Pump-jet propulsion is available as an option on most outboard motors. Although less efficient than an open propeller, they are particularly useful in applications where the ability to operate in very shallow water is important. They also eliminate the laceration dangers of an open propeller.

History and developments[edit]

The first known outboard motor was a small 5 kilogram electric unit designed around 1870 by Gustave Trouvé,[3] and patented in May 1880 (Patent N° 136,560).[4] Later about 25 petrol powered outboards may have been produced in 1896 by American Motors Co[3]—but neither of these two pioneering efforts appear to have had much impact.

The Waterman outboard engine appears to be the first real gasoline-powered outboard offered for sale.[5] Developed by Cameron Waterman, a young Yale Engineering student, it was developed from 1903, with a patent application filed in 1905[6] Starting in 1906,[7][8] the company went on to make thousands of his "Porto-Motor"[9] units,[10] claiming 25,000 sales by 1914.[11] The inboard boat motor firm of Caille Motor Company of Detroit were instrumental in making the cylinder and engines.

The most successful early outboard motor,[10] was created by Norwegian-American inventor Ole Evinrude in 1909.[12] Between 1909 and 1912, Evinrude made thousands of his outboards and the three horse units were sold around the world. His Evinrude Outboard Co. was spun off to other owners, and he went onto success with ELTO. The 1920s were the first high-water mark for the outboard with Evinrude, Johnson, ELTO, Atwater Lockwood and dozens of other makers in the field.

Historically, a majority of outboards have been two-stroke powerheads fitted with a carburetor due to the design's inherent simplicity, reliability, low cost and light weight. Drawbacks include increased pollution, due to the high volume of unburned gasoline in their exhaust, and louder noise.

Although four stroke outboards have been sold since the late 1920s, particulalrly Roness and Sharland, in 1962 Homelite introduced a commercially viable four cycle outboard a 55 horsepower motor, based on the 4 cylinder Crossley automobile engine. This was called the Bearcat that was later purchased by Fischer-Pierce who are the makers of Boston Whaler for use in their boats because of their technical superiority and efficiency over two strokes. In the early 1980s Honda Motor Co. introduced its first four-stroke powerhead.[13] In 1984, Yamaha introduced their first four-stroke powerhead. These motors were only available in the smaller hp range. In 1990 Honda released 35 hp and 45 hp four-stroke models. They continued to lead in the developement of four-stroke engines throughout the 1990s as US and European exhaust emissions regulations such as CARB (California Air Resources Board) led to the proliferation of four-stroke outboards. At first, North American manufacturers such as Mercury and OMC used engine technology from Japanese manufacturers such as Yamaha and Suzuki until they were able to develop their own four-stroke engine. The inherent advantages of four-stroke motors included: noise reduction, increase fuel economy, low end torque, and smoother operation.

Honda Marine Group, Mercury Marine, Mercury Racing, Nissan Marine, Suzuki Marine, Tohatsu Outboards, Yamaha Marine, and China Oshen-Hyfong marine have all developed new four-stroke engines. Some are carburetted, usually the smaller engines. The balance are electronically fuel-injected. Depending on the manufacturer, newer engines benefit from advanced technology such as multiple valves per cylinder, variable camshaft timing (Honda's VTEC), boosted low end torque (Honda's BLAST), 3-way cooling systems, and closed loop fuel injection. Mercury Verado four-strokes are unique in that they are supercharged.

Mercury Marine, Mercury Racing, Tohatsu, Yamaha Marine, Nissan and Evinrude each developed computer-controlled direct-injected two-stroke engines. Each brand boasts a different method of DI.

Fuel economy on both direct injected and four-stroke outboards measures from a 10 percent to 80 percent improvement, compared with conventional two-strokes. Depending on rpm and load at cruising speeds, figure on about a 30 percent mileage improvement.[14]

Outboard motor selection[edit]

It is important to select a motor that is a good match for the hull in terms of power and shaft length.

Power requirements[edit]

Overpowering is a dangerous condition[15] and underpowering often results in a boat that is incapable of performing in the role for which it was acquired. Boats built in the U.S. have a Coast Guard Rating Plate which specifies the maximum recommended horsepower for the hull. A motor with less than 75% of the maximum will most likely result in unsatisfactory performance.

Shaft length[edit]

Outboard motor shaft lengths are standardized to fit 15-inch, 20-inch and 25-inch transoms. If the shaft is too long it will extend farther into the water than necessary creating drag, which will impair performance and fuel economy. If the shaft is too short, the motor will be prone to ventilation. Even worse, if the water intake ports on the lower unit are not sufficiently submerged, engine overheating is likely, which can result in severe damages.

Operational issues[edit]

Motor mounting height[edit]

Motor height on the transom is an important factor in achieving optimal performance. The motor should be as high as possible without ventilating or loss of water pressure. This minimizes the effect of hydrodynamic drag while underway, allowing for greater speed. Generally, the antiventilation plate should be about the same height as, or up to two inches higher than, the keel, with the motor in neutral trim.

Trim[edit]

Trim is the angle of the motor in relation to the hull, as illustrated below. The ideal trim angle is the one in which the boat rides level, with most of the hull on the surface instead of plowing through the water.
Neutral trim Trimmed in Trimmed out
If the motor is trimmed out too far, the bow will ride too high in the water. With too little trim, the bow rides too low. The optimal trim setting will vary depending on many factors including speed, hull design, weight and balance, and conditions on the water (wind and waves). Many large outboards are equipped with power trim, an electric motor on the mounting bracket, with a switch at the helm that enables the operator to adjust the trim angle on the fly. In this case, the motor should be trimmed fully in to start, and trimmed out (with an eye on the tachometer) as the boat gains momentum, until it reaches the point just before ventilation begins or further trim adjustment results in an RPM increase with no increase in speed. Motors not equipped with power trim are manually adjustable using a pin called a topper tilt lock.

Ventilation[edit]

Ventilation is a phenomenon that occurs when surface air or exhaust gas (in the case of motors equipped with through-hub exhaust) is drawn into the spinning propeller blades. With the propeller pushing mostly air instead of water, the load on the engine is greatly reduced, causing the engine to race and the prop to spin fast enough to result in cavitation, at which point little thrust is generated at all. The condition continues until the prop slows enough for the air bubbles to rise to the surface.[16] The primary causes of ventilation are: motor mounted too high, motor trimmed out excessively, damage to the antiventilation plate, damage to propeller, foreign object lodged in the diffuser ring.

Safety[edit]

If the helmsman goes overboard, the boat may continue under power but uncontrolled, risking serious or fatal injuries to the helmsman and others in the water. A safety measure is a "kill cord" attached to the boat and helmsman, which cuts the motor if the helmsman falls overboard.[17]

Other Outboard Motoring Method[edit]

Vietnamese-style "Shrimp Tail Outboard Motor" Schematic. Design probably adapted decades ago from predecessors of Kohler Long tail Outboard Motor.

In Vietnam and perhaps other parts of South East Asia such as Thailand, designs perhaps adapted from the predecessors of one such as this Kohler Long Tail,[18] using locally materials are used until the present. In Vietnam, they are called "May Duoi Tom"(Shrimp Tail Motor). The outboard motors, which can be smallish air-cooled or water-cooled gasoline, diesel or even modified automotive engines, are bolted to a welded steel tube frame, with another long steel tube up to 3 m long to hold the drive shaft, driving a conventional looking propeller. The frame that holds the motor has a short, swiveling steel pin/tube approximately 15 cm long underneath, to be inserted into a corresponding hole on the transom, or a solid block or wood purposely built-in thereof.,[19][20][21][22][23] This drop-in arrangement enables extremely quick transfer of the motor to another boat or for storage - all that is needed is to lift it out. The pivoting design allows the outboard motor to be swiveled by the operator in almost all directions: Sideways for direction, up and down to change the thrust line according to speed or bow lift, elevate completely out of water for easy starting, placing the drive shaft and the propeller forward along the side of the boat for reverse, or put them inside the boat for propeller replacement, which can be a regular occurrence to the cheap cast aluminum propellers on the often debris-prone inland waterways.

Manufacturers[edit]

See also[edit]

References[edit]

  1. ^ Wordford, Chris. "Outboard Motors". Retrieved 9 February 2012. 
  2. ^ "Seven-Marine.com: "Seven Marine's 557 Horsepower V-8 Supercharged Outboard."". Retrieved 2011-06-07. 
  3. ^ a b Olsson, Kent. "THE OUTBOARD MOTORS". Säffle Marinmotor Museum. Retrieved 14 February 2012. 
  4. ^ Desmond, Kevin. "A Brief History of Electric Water Speed Records". electric record team. Retrieved 14 February 2012. 
  5. ^ "Kiekhaefer Will Fete Inventor of Outboard Motor", The Milwaukee Sentinel - Jan 16, 1955
  6. ^ "BOAT-PROPELLING DEVICBOAT-PROPELLING DEVICE", US Patent 851,389
  7. ^ "The Original Outboard Motor", Bob Zipps, July 1988, The Antique Outboarder]
  8. ^ "The History of Outboards", originally from: Bob Whittier, 1957, Yachting Magazine
  9. ^ "Some early Porto-Motor advertisements", Rowboat Motor Journal, Vol 2, Issue 1, 2009
  10. ^ a b "The Outboard Motor Turns 100", boatingmag.com
  11. ^ "Waterman PORTO Does It". The Independent. Jul 6, 1914. Retrieved August 1, 2012. 
  12. ^ "Colorful rivalry of outboard giants ...", jsonline.com
  13. ^ "Outboard Engines". 
  14. ^ "Two-Stroke versus Four-Stroke: Who's the Winner?". Retrieved 2008-06-15. 
  15. ^ Standards for Backyard Boat Builders (COMTDPUB P16761.3B), United States Coast Guard, Summer 1993 [1]
  16. ^ Carlton, John S., Marine Propellers and Propulsion, Elsevier, Ltd., 1994, ISBN 978-0-7506-8150-6
  17. ^ Royal Yachting Association: Use your kill cord, 30 April 2013
  18. ^ http://www.gandermountain.com/modperl/product/details.cgi?pdesc=Beavertail-6-HP-Kohler-All-Aluminum-Long-Tail-Motor&i=422067
  19. ^ http://i1051.photobucket.com/albums/s433/HungMTA/Mtchicvli.jpg
  20. ^ http://i1051.photobucket.com/albums/s433/HungMTA/Mytutrngrtd.jpg
  21. ^ http://dantri.vcmedia.vn/Uploaded/2011/02/08/du-xuan-mien-Tay1.jpg
  22. ^ http://farm5.static.flickr.com/4013/4476235603_a74f02303f.jpg
  23. ^ http://images.psndealer.com/dealersite%2Fimages%2Fnewvehicles%2Fnv138300_0.jpg
  24. ^ Bolinder trim story

External links[edit]

Patents[edit]


Original courtesy of Wikipedia: http://en.wikipedia.org/wiki/Outboard_motor — Please support Wikipedia.
This page uses Creative Commons Licensed content from Wikipedia. A portion of the proceeds from advertising on Digplanet goes to supporting Wikipedia.

479 news items

Basinsradio

Basinsradio
Fri, 29 Aug 2014 02:22:30 -0700

Crime Stoppers needs your help in solving a theft that occurred in a storage lot located at 507 Commercial Dr. between the dates of 08-01-14 and 08-24-14. During this time frame unknown suspect(s) stole a 2005 9.9 horsepower Mercury Outboard motor off ...
 
The Star Democrat
Fri, 29 Aug 2014 02:09:29 -0700

CHESTERTOWN — The Queen Anne's County Sheriff's Office is investigating the theft of an outboard motor from a boat on Sunday, Aug. 10. Turner Smith of the 200-block of Round Top Road said the missing motor is a black Yamaha four-stroke that was on ...

All At Sea

All At Sea
Sat, 23 Aug 2014 07:26:15 -0700

Evinrude, owned by Canada-based BRP (Bombardier Recreational Products) since 2001, introduced the E-TEC G2 outboard motor in Milwaukee at its Global Reveal in June. The sleek, customizable and completely redesigned cowl comes with a choice of ...

MarineLink

MarineLink
Tue, 19 Aug 2014 12:30:00 -0700

Elco Motor Yachts, a company in electric and hybrid marine propulsion for more than 120 years, is applying its expertise to the electric outboard motor category. The company is launching a new line of 5- and 7-horsepower motors, with an additional ...
 
Trade Only Today
Fri, 22 Aug 2014 08:33:45 -0700

Elco Motor Yachts, a builder of electric and hybrid marine propulsion for more than 120 years, is entering the electric outboard motor category. The New York state-based company is initially launching a new line of 5- and 7-horsepower motors and will ...

All At Sea

All At Sea
Tue, 12 Aug 2014 10:15:00 -0700

Suzuki Marine, the undisputed 4-stroke outboard brand on the world stage, is focused on gaining market share in North America where it is playing catch-up. Known for technical innovation, Suzuki has plenty of National Marine Manufacturers Association ...

Plymouth Herald

Plymouth Herald
Sun, 03 Aug 2014 05:56:15 -0700

The motor is a Mariner 25 in blue and grey. It has two large black handles at the rear of the engine ,a steel steering bracket and a red handle for the changing pivot point. Anyone who has information about the current whereabouts, or who saw ...

Stuff.co.nz

Stuff.co.nz
Mon, 01 Sep 2014 14:14:07 -0700

Coastguard Mana is off the water for at least two weeks after a $12,000 outboard motor was stolen from their only boat. The engine was recovered yesterday afternoon after being taken on Saturday night, but it would take a fortnight to repair the ...
Loading

Oops, we seem to be having trouble contacting Twitter

Talk About Outboard motor

You can talk about Outboard motor with people all over the world in our discussions.

Support Wikipedia

A portion of the proceeds from advertising on Digplanet goes to supporting Wikipedia. Please add your support for Wikipedia!