digplanet beta 1: Athena
Share digplanet:


Applied sciences






















For the indie film, see Microphone (film).
"Microphones" redirects here. For the indie band, see The Microphones.
An AKG C214 condenser microphone with shock mount
A Sennheiser dynamic microphone

A microphone, colloquially mic or mike (/ˈmk/),[1] is an acoustic-to-electric transducer or sensor that converts sound in air into an electrical signal. Microphones are used in many applications such as telephones, hearing aids, public address systems for concert halls and public events, motion picture production, live and recorded audio engineering, two-way radios, megaphones, radio and television broadcasting, and in computers for recording voice, speech recognition, VoIP, and for non-acoustic purposes such as ultrasonic checking or knock sensors.

Most microphones today use electromagnetic induction (dynamic microphones), capacitance change (condenser microphones) or piezoelectricity (piezoelectric microphones) to produce an electrical signal from air pressure variations. Microphones typically need to be connected to a preamplifier before the signal can be amplified with an audio power amplifier or recorded.


In order to speak to larger groups of people, there was a desire to increase the volume of the spoken word. The earliest known device to achieve this dates to 600 BC with the invention of masks with specially designed mouth openings that acoustically augmented the voice in amphitheatres.[2] In 1665, the English physicist Robert Hooke was the first to experiment with a medium other than air with the invention of the "lovers' telephone" made of stretched wire with a cup attached at each end.[3]

German inventor Johann Philipp Reis designed an early sound transmitter that used a metallic strip attached to a vibrating membrane that would produce intermittent current. Better results were achieved with the 'liquid transmitter' design in Scottish-American Alexander Graham Bell's telephone of 1876 – the diaphragm was attached to a conductive rod in an acid solution.[4] These systems, however, gave a very poor sound quality.

Carbon microphone[edit]

Main article: Carbon microphone
David Edward Hughes invented a carbon microphone in the 1870s.

The first microphone that enabled proper voice telephony was the (loose-contact) carbon microphone (then called transmitter). This was independently developed by David Edward Hughes in England and Emile Berliner and Thomas Edison in the US. Although Edison was awarded the first patent (after a long legal dispute) in mid-1877, Hughes had demonstrated his working device in front of many witnesses some years earlier, and most historians credit him with its invention.[5][6][7][8]

Hughes' device used loosely packed carbon granules – the varying pressure exerted on the granules by the diaphragm from the acoustic waves caused the resistance of the carbon to vary proportionally, allowing a relatively accurate electrical reproduction of the sound signal. Hughes also coined the word microphone. He demonstrated his apparatus to the Royal Society by magnifying the sound of insects scratching through a sound box. Contrary to Edison, Hughes decided not to take out a patent; instead he gave his invention as a gift to the world.[9]

The carbon microphone is the direct prototype of today's microphones and was critical in the development of telephony, broadcasting and the recording industries.[10]

Thomas Edison refined the carbon microphone into his carbon-button transmitter of 1886.[7][9] This microphone was employed at the first ever radio broadcast, a performance at the New York Metropolitan Opera House in 1910.[11]

Further developments[edit]

In 1916, C. Wente of Bell Labs developed the next breakthrough with the first condenser microphone.[12]

Jack Brown interviews Humphrey Bogart and Lauren Bacall for broadcast to troops overseas during World War II.

In 1923 the first practical moving coil microphone was built. "The Marconi Skykes" or "magnetophon", developed by Captain H. J. Round, was the standard for BBC studios in London.[13] This was improved in 1930 by Blumlein and Holman who released the HB1A and was the best standard of the day.[14]

In the same year, the ribbon microphone was introduced, another electromagnetic type, believed to have been developed by Harry F. Olson, who essentially reverse-engineered a ribbon speaker.[15] Over the years these microphones were developed by several companies, most notably RCA that made large advancements in pattern control, to give the microphone directionality. With television and film technology booming there was demand for high fidelity microphones and greater directionality. Electro-Voice responded with their Academy Award-winning shotgun microphone in 1963.

During the second half of 20th century development advanced quickly with the Shure Brothers bringing out the SM58 and SM57. Digital was pioneered by Milab in 1999 with the DM-1001.[16] The latest research developments include the use of fibre optics, lasers and interferometers.


Electronic symbol for a microphone

The sensitive transducer element of a microphone is called its element or capsule. Except in thermophone based microphones, sound is first converted to mechanical motion by means of a diaphragm, the motion of which is then converted to an electrical signal. A complete microphone also includes a housing, some means of bringing the signal from the element to other equipment, and often an electronic circuit to adapt the output of the capsule to the equipment being driven. A wireless microphone contains a radio transmitter.


Microphones are referred to by their transducer principle, such as condenser, dynamic, etc., and by their directional characteristics. Sometimes other characteristics such as diaphragm size, intended use or orientation of the principal sound input to the principal axis (end- or side-address) of the microphone are used to describe the microphone.

Condenser microphone[edit]

Inside the Oktava 319 condenser microphone

The condenser microphone, invented at Bell Labs in 1916 by E. C. Wente[17] is also called a capacitor microphone or electrostatic microphone—capacitors were historically called condensers. Here, the diaphragm acts as one plate of a capacitor, and the vibrations produce changes in the distance between the plates. There are two types, depending on the method of extracting the audio signal from the transducer: DC-biased microphones, and radio frequency (RF) or high frequency (HF) condenser microphones. With a DC-biased microphone, the plates are biased with a fixed charge (Q). The voltage maintained across the capacitor plates changes with the vibrations in the air, according to the capacitance equation (C = QV), where Q = charge in coulombs, C = capacitance in farads and V = potential difference in volts. The capacitance of the plates is inversely proportional to the distance between them for a parallel-plate capacitor. (See capacitance for details.) The assembly of fixed and movable plates is called an "element" or "capsule".

A nearly constant charge is maintained on the capacitor. As the capacitance changes, the charge across the capacitor does change very slightly, but at audible frequencies it is sensibly constant. The capacitance of the capsule (around 5 to 100 pF) and the value of the bias resistor (100  to tens of GΩ) form a filter that is high-pass for the audio signal, and low-pass for the bias voltage. Note that the time constant of an RC circuit equals the product of the resistance and capacitance.

Within the time-frame of the capacitance change (as much as 50 ms at 20 Hz audio signal), the charge is practically constant and the voltage across the capacitor changes instantaneously to reflect the change in capacitance. The voltage across the capacitor varies above and below the bias voltage. The voltage difference between the bias and the capacitor is seen across the series resistor. The voltage across the resistor is amplified for performance or recording. In most cases, the electronics in the microphone itself contribute no voltage gain as the voltage differential is quite significant, up to several volts for high sound levels. Since this is a very high impedance circuit, current gain only is usually needed, with the voltage remaining constant.

AKG C451B small-diaphragm condenser microphone

RF condenser microphones use a comparatively low RF voltage, generated by a low-noise oscillator. The signal from the oscillator may either be amplitude modulated by the capacitance changes produced by the sound waves moving the capsule diaphragm, or the capsule may be part of a resonant circuit that modulates the frequency of the oscillator signal. Demodulation yields a low-noise audio frequency signal with a very low source impedance. The absence of a high bias voltage permits the use of a diaphragm with looser tension, which may be used to achieve wider frequency response due to higher compliance. The RF biasing process results in a lower electrical impedance capsule, a useful by-product of which is that RF condenser microphones can be operated in damp weather conditions that could create problems in DC-biased microphones with contaminated insulating surfaces. The Sennheiser "MKH" series of microphones use the RF biasing technique.

Condenser microphones span the range from telephone transmitters through inexpensive karaoke microphones to high-fidelity recording microphones. They generally produce a high-quality audio signal and are now the popular choice in laboratory and recording studio applications. The inherent suitability of this technology is due to the very small mass that must be moved by the incident sound wave, unlike other microphone types that require the sound wave to do more work. They require a power source, provided either via microphone inputs on equipment as phantom power or from a small battery. Power is necessary for establishing the capacitor plate voltage, and is also needed to power the microphone electronics (impedance conversion in the case of electret and DC-polarized microphones, demodulation or detection in the case of RF/HF microphones). Condenser microphones are also available with two diaphragms that can be electrically connected to provide a range of polar patterns (see below), such as cardioid, omnidirectional, and figure-eight. It is also possible to vary the pattern continuously with some microphones, for example the Røde NT2000 or CAD M179.

A valve microphone is a condenser microphone that uses a vacuum tube (valve) amplifier.[18] They remain popular with enthusiasts of tube sound.

Electret condenser microphone[edit]

Main article: Electret microphone
First patent on foil electret microphone by G. M. Sessler et al. (pages 1 to 3)

An electret microphone is a type of capacitor microphone invented by Gerhard Sessler and Jim West at Bell laboratories in 1962.[19] The externally applied charge described above under condenser microphones is replaced by a permanent charge in an electret material. An electret is a ferroelectric material that has been permanently electrically charged or polarized. The name comes from electrostatic and magnet; a static charge is embedded in an electret by alignment of the static charges in the material, much the way a magnet is made by aligning the magnetic domains in a piece of iron.

Due to their good performance and ease of manufacture, hence low cost, the vast majority of microphones made today are electret microphones; a semiconductor manufacturer[20] estimates annual production at over one billion units. Nearly all cell-phone, computer, PDA and headset microphones are electret types. They are used in many applications, from high-quality recording and lavalier use to built-in microphones in small sound recording devices and telephones. Though electret microphones were once considered low quality, the best ones can now rival traditional condenser microphones in every respect and can even offer the long-term stability and ultra-flat response needed for a measurement microphone. Unlike other capacitor microphones, they require no polarizing voltage, but often contain an integrated preamplifier that does require power (often incorrectly called polarizing power or bias). This preamplifier is frequently phantom powered in sound reinforcement and studio applications. Monophonic microphones designed for personal computer (PC) use, sometimes called multimedia microphones, use a 3.5&mm plug as usually used, without power, for stereo; the ring, instead of carrying the signal for a second channel, carries power via a resistor from (normally) a 5 V supply in the computer. Stereophonic microphones use the same connector; there is no obvious way to determine which standard is used by equipment and microphones.

Only the best electret microphones rival good DC-polarized units in terms of noise level and quality; electret microphones lend themselves to inexpensive mass-production, while inherently expensive non-electret condenser microphones are made to higher quality.

Dynamic microphone[edit]

Patti Smith singing into a Shure SM58 (dynamic cardioid type) microphone

Dynamic microphones work via electromagnetic induction. They are robust, relatively inexpensive and resistant to moisture. This, coupled with their potentially high gain before feedback, makes them ideal for on-stage use.

Moving-coil microphones use the same dynamic principle as in a loudspeaker, only reversed. A small movable induction coil, positioned in the magnetic field of a permanent magnet, is attached to the diaphragm. When sound enters through the windscreen of the microphone, the sound wave moves the diaphragm. When the diaphragm vibrates, the coil moves in the magnetic field, producing a varying current in the coil through electromagnetic induction. A single dynamic membrane does not respond linearly to all audio frequencies. Some microphones for this reason utilize multiple membranes for the different parts of the audio spectrum and then combine the resulting signals. Combining the multiple signals correctly is difficult and designs that do this are rare and tend to be expensive. There are on the other hand several designs that are more specifically aimed towards isolated parts of the audio spectrum. The AKG D 112, for example, is designed for bass response rather than treble.[21] In audio engineering several kinds of microphones are often used at the same time to get the best result.

Ribbon microphone[edit]

Main article: Ribbon microphone
Edmund Lowe using a ribbon microphone

Ribbon microphones use a thin, usually corrugated metal ribbon suspended in a magnetic field. The ribbon is electrically connected to the microphone's output, and its vibration within the magnetic field generates the electrical signal. Ribbon microphones are similar to moving coil microphones in the sense that both produce sound by means of magnetic induction. Basic ribbon microphones detect sound in a bi-directional (also called figure-eight, as in the diagram below) pattern because the ribbon, which is open to sound both front and back, responds to the pressure gradient rather than the sound pressure. Though the symmetrical front and rear pickup can be a nuisance in normal stereo recording, the high side rejection can be used to advantage by positioning a ribbon microphone horizontally, for example above cymbals, so that the rear lobe picks up only sound from the cymbals. Crossed figure 8, or Blumlein pair, stereo recording is gaining in popularity, and the figure 8 response of a ribbon microphone is ideal for that application.

Other directional patterns are produced by enclosing one side of the ribbon in an acoustic trap or baffle, allowing sound to reach only one side. The classic RCA Type 77-DX microphone has several externally adjustable positions of the internal baffle, allowing the selection of several response patterns ranging from "Figure-8" to "Unidirectional". Such older ribbon microphones, some of which still provide high quality sound reproduction, were once valued for this reason, but a good low-frequency response could only be obtained when the ribbon was suspended very loosely, which made them relatively fragile. Modern ribbon materials, including new nanomaterials[22] have now been introduced that eliminate those concerns, and even improve the effective dynamic range of ribbon microphones at low frequencies. Protective wind screens can reduce the danger of damaging a vintage ribbon, and also reduce plosive artifacts in the recording. Properly designed wind screens produce negligible treble attenuation. In common with other classes of dynamic microphone, ribbon microphones don't require phantom power; in fact, this voltage can damage some older ribbon microphones. Some new modern ribbon microphone designs incorporate a preamplifier and, therefore, do require phantom power, and circuits of modern passive ribbon microphones, i.e., those without the aforementioned preamplifier, are specifically designed to resist damage to the ribbon and transformer by phantom power. Also there are new ribbon materials available that are immune to wind blasts and phantom power.

Carbon microphone[edit]

Main article: Carbon microphone

A carbon microphone, also known as a carbon button microphone (or sometimes just a button microphone), uses a capsule or button containing carbon granules pressed between two metal plates like the Berliner and Edison microphones. A voltage is applied across the metal plates, causing a small current to flow through the carbon. One of the plates, the diaphragm, vibrates in sympathy with incident sound waves, applying a varying pressure to the carbon. The changing pressure deforms the granules, causing the contact area between each pair of adjacent granules to change, and this causes the electrical resistance of the mass of granules to change. The changes in resistance cause a corresponding change in the current flowing through the microphone, producing the electrical signal. Carbon microphones were once commonly used in telephones; they have extremely low-quality sound reproduction and a very limited frequency response range, but are very robust devices. The Boudet microphone, which used relatively large carbon balls, was similar to the granule carbon button microphones.[23]

Unlike other microphone types, the carbon microphone can also be used as a type of amplifier, using a small amount of sound energy to control a larger amount of electrical energy. Carbon microphones found use as early telephone repeaters, making long distance phone calls possible in the era before vacuum tubes. These repeaters worked by mechanically coupling a magnetic telephone receiver to a carbon microphone: the faint signal from the receiver was transferred to the microphone, where it modulated a stronger electric current, producing a stronger electrical signal to send down the line. One illustration of this amplifier effect was the oscillation caused by feedback, resulting in an audible squeal from the old "candlestick" telephone if its earphone was placed near the carbon microphone.

Piezoelectric microphone[edit]

A crystal microphone or piezo microphone uses the phenomenon of piezoelectricity—the ability of some materials to produce a voltage when subjected to pressure—to convert vibrations into an electrical signal. An example of this is potassium sodium tartrate, which is a piezoelectric crystal that works as a transducer, both as a microphone and as a slimline loudspeaker component. Crystal microphones were once commonly supplied with vacuum tube (valve) equipment, such as domestic tape recorders. Their high output impedance matched the high input impedance (typically about 10 megohms) of the vacuum tube input stage well. They were difficult to match to early transistor equipment, and were quickly supplanted by dynamic microphones for a time, and later small electret condenser devices. The high impedance of the crystal microphone made it very susceptible to handling noise, both from the microphone itself and from the connecting cable.

Piezoelectric transducers are often used as contact microphones to amplify sound from acoustic musical instruments, to sense drum hits, for triggering electronic samples, and to record sound in challenging environments, such as underwater under high pressure. Saddle-mounted pickups on acoustic guitars are generally piezoelectric devices that contact the strings passing over the saddle. This type of microphone is different from magnetic coil pickups commonly visible on typical electric guitars, which use magnetic induction, rather than mechanical coupling, to pick up vibration.

Fiber optic microphone[edit]

The Optoacoustics 1140 fiber optic microphone

A fiber optic microphone converts acoustic waves into electrical signals by sensing changes in light intensity, instead of sensing changes in capacitance or magnetic fields as with conventional microphones.[24][25]

During operation, light from a laser source travels through an optical fiber to illuminate the surface of a reflective diaphragm. Sound vibrations of the diaphragm modulate the intensity of light reflecting off the diaphragm in a specific direction. The modulated light is then transmitted over a second optical fiber to a photo detector, which transforms the intensity-modulated light into analog or digital audio for transmission or recording. Fiber optic microphones possess high dynamic and frequency range, similar to the best high fidelity conventional microphones.

Fiber optic microphones do not react to or influence any electrical, magnetic, electrostatic or radioactive fields (this is called EMI/RFI immunity). The fiber optic microphone design is therefore ideal for use in areas where conventional microphones are ineffective or dangerous, such as inside industrial turbines or in magnetic resonance imaging (MRI) equipment environments.

Fiber optic microphones are robust, resistant to environmental changes in heat and moisture, and can be produced for any directionality or impedance matching. The distance between the microphone's light source and its photo detector may be up to several kilometers without need for any preamplifier or other electrical device, making fiber optic microphones suitable for industrial and surveillance acoustic monitoring.

Fiber optic microphones are used in very specific application areas such as for infrasound monitoring and noise-canceling. They have proven especially useful in medical applications, such as allowing radiologists, staff and patients within the powerful and noisy magnetic field to converse normally, inside the MRI suites as well as in remote control rooms.[26] Other uses include industrial equipment monitoring and sensing, audio calibration and measurement, high-fidelity recording and law enforcement.

Laser microphone[edit]

Main article: Laser microphone

Laser microphones are often portrayed in movies as spy gadgets, because they can be used to pick up sound at a distance from the microphone equipment. A laser beam is aimed at the surface of a window or other plane surface that is affected by sound. The vibrations of this surface change the angle at which the beam is reflected, and the motion of the laser spot from the returning beam is detected and converted to an audio signal.

In a more robust and expensive implementation, the returned light is split and fed to an interferometer, which detects movement of the surface by changes in the optical path length of the reflected beam. The former implementation is a tabletop experiment; the latter requires an extremely stable laser and precise optics.

A new type of laser microphone is a device that uses a laser beam and smoke or vapor to detect sound vibrations in free air. On 25 August 2009, U.S. patent 7,580,533 issued for a Particulate Flow Detection Microphone based on a laser-photocell pair with a moving stream of smoke or vapor in the laser beam's path. Sound pressure waves cause disturbances in the smoke that in turn cause variations in the amount of laser light reaching the photo detector. A prototype of the device was demonstrated at the 127th Audio Engineering Society convention in New York City from 9 through 12 October 2009.

Liquid microphone[edit]

Main article: Water microphone

Early microphones did not produce intelligible speech, until Alexander Graham Bell made improvements including a variable-resistance microphone/transmitter. Bell's liquid transmitter consisted of a metal cup filled with water with a small amount of sulfuric acid added. A sound wave caused the diaphragm to move, forcing a needle to move up and down in the water. The electrical resistance between the wire and the cup was then inversely proportional to the size of the water meniscus around the submerged needle. Elisha Gray filed a caveat for a version using a brass rod instead of the needle. Other minor variations and improvements were made to the liquid microphone by Majoranna, Chambers, Vanni, Sykes, and Elisha Gray, and one version was patented by Reginald Fessenden in 1903. These were the first working microphones, but they were not practical for commercial application. The famous first phone conversation between Bell and Watson took place using a liquid microphone.

MEMS microphone[edit]

The MEMS (MicroElectrical-Mechanical System) microphone is also called a microphone chip or silicon microphone. The pressure-sensitive diaphragm is etched directly into a silicon chip by MEMS techniques, and is usually accompanied with integrated preamplifier. Most MEMS microphones are variants of the condenser microphone design. Often MEMS microphones have built in analog-to-digital converter (ADC) circuits on the same CMOS chip making the chip a digital microphone and so more readily integrated with modern digital products. Major manufacturers producing MEMS silicon microphones are Wolfson Microelectronics (WM7xxx), Analog Devices, Akustica (AKU200x), Infineon (SMM310 product), Knowles Electronics, Memstech (MSMx), NXP Semiconductors, Sonion MEMS, AAC Acoustic Technologies,[27] and Omron.[28]

Speakers as microphones[edit]

A loudspeaker, a transducer that turns an electrical signal into sound waves, is the functional opposite of a microphone. Since a conventional speaker is constructed much like a dynamic microphone (with a diaphragm, coil and magnet), speakers can actually work "in reverse" as microphones. The result, though, is a microphone with poor quality, limited frequency response (particularly at the high end), and poor sensitivity. In practical use, speakers are sometimes used as microphones in applications where high quality and sensitivity are not needed such as intercoms, walkie-talkies or video game voice chat peripherals, or when conventional microphones are in short supply.

However, there is at least one other practical application of this principle: Using a medium-size woofer placed closely in front of a "kick" (bass drum) in a drum set to act as a microphone. The use of relatively large speakers to transduce low frequency sound sources, especially in music production, is becoming fairly common. A product example of this type of device is the Yamaha Subkick, a 6.5-inch (170 mm) woofer shock-mounted into a 10" (254 mm) drum shell used in front of kick drums. Since a relatively massive membrane is unable to transduce high frequencies, placing a speaker in front of a kick drum is often ideal for reducing cymbal and snare bleed into the kick drum sound. Less commonly, microphones themselves can be used as speakers, almost always as tweeters. Microphones, however, are not designed to handle the power that speaker components are routinely required to cope with. One instance of such an application was the STC microphone-derived 4001 super-tweeter, which was successfully used in a number of high quality loudspeaker systems from the late 1960s to the mid-70s.

Capsule design and directivity[edit]

The inner elements of a microphone are the primary source of differences in directivity. A pressure microphone uses a diaphragm between a fixed internal volume of air and the environment, and responds uniformly to pressure from all directions, so it is said to be omnidirectional. A pressure-gradient microphone uses a diaphragm that is at least partially open on both sides. The pressure difference between the two sides produces its directional characteristics. Other elements such as the external shape of the microphone and external devices such as interference tubes can also alter a microphone's directional response. A pure pressure-gradient microphone is equally sensitive to sounds arriving from front or back, but insensitive to sounds arriving from the side because sound arriving at the front and back at the same time creates no gradient between the two. The characteristic directional pattern of a pure pressure-gradient microphone is like a figure-8. Other polar patterns are derived by creating a capsule that combines these two effects in different ways. The cardioid, for instance, features a partially closed backside, so its response is a combination of pressure and pressure-gradient characteristics.[29]

Microphone polar patterns[edit]

(Microphone facing top of page in diagram, parallel to page):

A microphone's directionality or polar pattern indicates how sensitive it is to sounds arriving at different angles about its central axis. The polar patterns illustrated above represent the locus of points that produce the same signal level output in the microphone if a given sound pressure level (SPL) is generated from that point. How the physical body of the microphone is oriented relative to the diagrams depends on the microphone design. For large-membrane microphones such as in the Oktava (pictured above), the upward direction in the polar diagram is usually perpendicular to the microphone body, commonly known as "side fire" or "side address". For small diaphragm microphones such as the Shure (also pictured above), it usually extends from the axis of the microphone commonly known as "end fire" or "top/end address".

Some microphone designs combine several principles in creating the desired polar pattern. This ranges from shielding (meaning diffraction/dissipation/absorption) by the housing itself to electronically combining dual membranes.


An omnidirectional (or nondirectional) microphone's response is generally considered to be a perfect sphere in three dimensions. In the real world, this is not the case. As with directional microphones, the polar pattern for an "omnidirectional" microphone is a function of frequency. The body of the microphone is not infinitely small and, as a consequence, it tends to get in its own way with respect to sounds arriving from the rear, causing a slight flattening of the polar response. This flattening increases as the diameter of the microphone (assuming it's cylindrical) reaches the wavelength of the frequency in question. Therefore, the smallest diameter microphone gives the best omnidirectional characteristics at high frequencies.

The wavelength of sound at 10 kHz is little over an inch (3.4 cm). The smallest measuring microphones are often 1/4" (6 mm) in diameter, which practically eliminates directionality even up to the highest frequencies. Omnidirectional microphones, unlike cardioids, do not employ resonant cavities as delays, and so can be considered the "purest" microphones in terms of low coloration; they add very little to the original sound. Being pressure-sensitive they can also have a very flat low-frequency response down to 20 Hz or below. Pressure-sensitive microphones also respond much less to wind noise and plosives than directional (velocity sensitive) microphones.

An example of a nondirectional microphone is the round black eight ball.[30]


A unidirectional microphone is sensitive to sounds from only one direction. The diagram above illustrates a number of these patterns. The microphone faces upwards in each diagram. The sound intensity for a particular frequency is plotted for angles radially from 0 to 360°. (Professional diagrams show these scales and include multiple plots at different frequencies. The diagrams given here provide only an overview of typical pattern shapes, and their names.)


University Sound US664A dynamic supercardioid microphone

The most common unidirectional microphone is a cardioid microphone, so named because the sensitivity pattern is a cardioid. The cardioid family of microphones are commonly used as vocal or speech microphones, since they are good at rejecting sounds from other directions. In three dimensions, the cardioid is shaped like an apple centred around the microphone which is the "stalk" of the apple. The cardioid response reduces pickup from the side and rear, helping to avoid feedback from the monitors. Since pressure gradient transducer microphones are directional, putting them very close to the sound source (at distances of a few centimeters) results in a bass boost. This is known as the proximity effect.[31] The SM58 has been the most commonly used microphone for live vocals for more than 40 years[32] demonstrating the importance and popularity of cardioid mics.

A cardioid microphone is effectively a superposition of an omnidirectional and a figure-8 microphone; for sound waves coming from the back, the negative signal from the figure-8 cancels the positive signal from the omnidirectional element, whereas for sound waves coming from the front, the two add to each other. A hyper-cardioid microphone is similar, but with a slightly larger figure-8 contribution leading to a tighter area of front sensitivity and a smaller lobe of rear sensitivity. A super-cardioid microphone is similar to a hyper-cardioid, except there is more front pickup and less rear pickup. While any pattern between omni and figure 8 is possible by adjusting their mix, common definitions state that a hypercardioid is produced by combining them at a 3:1 ratio, producing nulls at 109.5°, while supercardioid is produced with a 5:3 ratio, with nulls at 126.9°.[33][34]


"Figure 8" or bi-directional microphones receive sound equally from both the front and back of the element. Most ribbon microphones are of this pattern. In principle they do not respond to sound pressure at all, only to the change in pressure between front and back; since sound arriving from the side reaches front and back equally there is no difference in pressure and therefore no sensitivity to sound from that direction. In more mathematical terms, while omnidirectional microphones are scalar transducers responding to pressure from any direction, bi-directional microphones are vector transducers responding to the gradient along an axis normal to the plane of the diaphragm. This also has the effect of inverting the output polarity for sounds arriving from the back side.

Shotgun and parabolic microphones[edit]

An Audio-Technica shotgun microphone

Shotgun microphones are the most highly directional. Their directional pattern has a very narrow lobe in the forward direction and rejects sound from other directions. They have small lobes of sensitivity to the left, right, and rear but are significantly less sensitive to the side and rear than other directional microphones. This results from placing the element at the back end of a tube with slots cut along the side; wave cancellation eliminates much of the off-axis sound. Due to the narrowness of their sensitivity area, shotgun microphones are commonly used on television and film sets, in stadiums, and for field recording of wildlife. Parabolic microphones have similar characteristics, but often have poorer bass response.

Boundary or "PZM"[edit]

Several approaches have been developed for effectively using a microphone in less-than-ideal acoustic spaces, which often suffer from excessive reflections from one or more of the surfaces (boundaries) that make up the space. If the microphone is placed in, or very close to, one of these boundaries, the reflections from that surface are not sensed by the microphone. Initially this was done by placing an ordinary microphone adjacent to the surface, sometimes in a block of acoustically transparent foam. Sound engineers Ed Long and Ron Wickersham developed the concept of placing the diaphragm parallel to and facing the boundary.[35] While the patent has expired, "Pressure Zone Microphone" and "PZM" are still active trademarks of Crown International, and the generic term "boundary microphone" is preferred. While a boundary microphone was initially implemented using an omnidirectional element, it is also possible to mount a directional microphone close enough to the surface to gain some of the benefits of this technique while retaining the directional properties of the element. Crown's trademark on this approach is "Phase Coherent Cardioid" or "PCC," but there are other makers who employ this technique as well.

Application-specific designs[edit]

A lavalier microphone is made for hands-free operation. These small microphones are worn on the body. Originally, they were held in place with a lanyard worn around the neck, but more often they are fastened to clothing with a clip, pin, tape or magnet. The lavalier cord may be hidden by clothes and either run to an RF transmitter in a pocket or clipped to a belt (for mobile use), or run directly to the mixer (for stationary applications).

A wireless microphone transmits the audio as a radio or optical signal rather than via a cable. It usually sends its signal using a small FM radio transmitter to a nearby receiver connected to the sound system, but it can also use infrared waves if the transmitter and receiver are within sight of each other.

A contact microphone picks up vibrations directly from a solid surface or object, as opposed to sound vibrations carried through air. One use for this is to detect sounds of a very low level, such as those from small objects or insects. The microphone commonly consists of a magnetic (moving coil) transducer, contact plate and contact pin. The contact plate is placed directly on the vibrating part of a musical instrument or other surface, and the contact pin transfers vibrations to the coil. Contact microphones have been used to pick up the sound of a snail's heartbeat and the footsteps of ants. A portable version of this microphone has recently been developed. A throat microphone is a variant of the contact microphone that picks up speech directly from a person's throat, which it is strapped to. This lets the device be used in areas with ambient sounds that would otherwise make the speaker inaudible.

A parabolic microphone uses a parabolic reflector to collect and focus sound waves onto a microphone receiver, in much the same way that a parabolic antenna (e.g. satellite dish) does with radio waves. Typical uses of this microphone, which has unusually focused front sensitivity and can pick up sounds from many meters away, include nature recording, outdoor sporting events, eavesdropping, law enforcement, and even espionage. Parabolic microphones are not typically used for standard recording applications, because they tend to have poor low-frequency response as a side effect of their design.

A stereo microphone integrates two microphones in one unit to produce a stereophonic signal. A stereo microphone is often used for broadcast applications or field recording where it would be impractical to configure two separate condenser microphones in a classic X-Y configuration (see microphone practice) for stereophonic recording. Some such microphones have an adjustable angle of coverage between the two channels.

A noise-canceling microphone is a highly directional design intended for noisy environments. One such use is in aircraft cockpits where they are normally installed as boom microphones on headsets. Another use is in live event support on loud concert stages for vocalists involved with live performances. Many noise-canceling microphones combine signals received from two diaphragms that are in opposite electrical polarity or are processed electronically. In dual diaphragm designs, the main diaphragm is mounted closest to the intended source and the second is positioned farther away from the source so that it can pick up environmental sounds to be subtracted from the main diaphragm's signal. After the two signals have been combined, sounds other than the intended source are greatly reduced, substantially increasing intelligibility. Other noise-canceling designs use one diaphragm that is affected by ports open to the sides and rear of the microphone, with the sum being a 16 dB rejection of sounds that are farther away. One noise-canceling headset design using a single diaphragm has been used prominently by vocal artists such as Garth Brooks and Janet Jackson.[36] A few noise-canceling microphones are throat microphones.


Electronic symbol for a microphone

The most common connectors used by microphones are:

  • Male XLR connector on professional microphones
  • ¼ inch (sometimes referred to as 6.3 mm) phone connector on less expensive consumer microphones, using an unbalanced 1/4 inch (6.3 mm) TS phone connector. Harmonica microphones commonly use a high impedance 1/4 inch (6.3 mm) TS connection to be run through guitar amplifiers.
  • 3.5 mm (sometimes referred to as 1/8 inch mini) stereo (wired as mono) mini phone plug on very inexpensive and computer microphones
A microphone with a USB connector, made by Blue Microphones

Some microphones use other connectors, such as a 5-pin XLR, or mini XLR for connection to portable equipment. Some lavalier (or 'lapel', from the days of attaching the microphone to the news reporters suit lapel) microphones use a proprietary connector for connection to a wireless transmitter, such as a radio pack. Since 2005, professional-quality microphones with USB connections have begun to appear, designed for direct recording into computer-based software.


Microphones have an electrical characteristic called impedance, measured in ohms (Ω), that depends on the design. Typically, the rated impedance is stated.[37] Low impedance is considered under 600 Ω. Medium impedance is considered between 600 Ω and 10 kΩ. High impedance is above 10 kΩ. Owing to their built-in amplifier, condenser microphones typically have an output impedance between 50 and 200 Ω.[38]

The output of a given microphone delivers the same power whether it is low or high impedance. If a microphone is made in high and low impedance versions, the high impedance version has a higher output voltage for a given sound pressure input, and is suitable for use with vacuum-tube guitar amplifiers, for instance, which have a high input impedance and require a relatively high signal input voltage to overcome the tubes' inherent noise. Most professional microphones are low impedance, about 200 Ω or lower. Professional vacuum-tube sound equipment incorporates a transformer that steps up the impedance of the microphone circuit to the high impedance and voltage needed to drive the input tube; the impedance conversion inherently creates voltage gain as well. External matching transformers are also available that can be used in-line between a low impedance microphone and a high impedance input.

Low-impedance microphones are preferred over high impedance for two reasons: one is that using a high-impedance microphone with a long cable results in high frequency signal loss due to cable capacitance, which forms a low-pass filter with the microphone output impedance. The other is that long high-impedance cables tend to pick up more hum (and possibly radio-frequency interference (RFI) as well). Nothing is damaged if the impedance between microphone and other equipment is mismatched; the worst that happens is a reduction in signal or change in frequency response.

Most microphones are designed not to have their impedance matched by the load they are connected to.[39] Doing so can alter their frequency response and cause distortion, especially at high sound pressure levels. Certain ribbon and dynamic microphones are exceptions, due to the designers' assumption of a certain load impedance being part of the internal electro-acoustical damping circuit of the microphone.[40][dubious ]

Digital microphone interface[edit]

Neumann D-01 digital microphone and Neumann DMI-8 8-channel USB Digital Microphone Interface

The AES 42 standard, published by the Audio Engineering Society, defines a digital interface for microphones. Microphones conforming to this standard directly output a digital audio stream through an XLR or XLD male connector, rather than producing an analog output. Digital microphones may be used either with new equipment with appropriate input connections that conform to the AES 42 standard, or else via a suitable interface box. Studio-quality microphones that operate in accordance with the AES 42 standard are now available from a number of microphone manufacturers.

Measurements and specifications[edit]

A comparison of the far field on-axis frequency response of the Oktava 319 and the Shure SM58

Because of differences in their construction, microphones have their own characteristic responses to sound. This difference in response produces non-uniform phase and frequency responses. In addition, microphones are not uniformly sensitive to sound pressure, and can accept differing levels without distorting. Although for scientific applications microphones with a more uniform response are desirable, this is often not the case for music recording, as the non-uniform response of a microphone can produce a desirable coloration of the sound. There is an international standard for microphone specifications,[37] but few manufacturers adhere to it. As a result, comparison of published data from different manufacturers is difficult because different measurement techniques are used. The Microphone Data Website has collated the technical specifications complete with pictures, response curves and technical data from the microphone manufacturers for every currently listed microphone, and even a few obsolete models, and shows the data for them all in one common format for ease of comparison.[3]. Caution should be used in drawing any solid conclusions from this or any other published data, however, unless it is known that the manufacturer has supplied specifications in accordance with IEC 60268-4.

A frequency response diagram plots the microphone sensitivity in decibels over a range of frequencies (typically 20 Hz to 20 kHz), generally for perfectly on-axis sound (sound arriving at 0° to the capsule). Frequency response may be less informatively stated textually like so: "30 Hz–16 kHz ±3 dB". This is interpreted as meaning a nearly flat, linear, plot between the stated frequencies, with variations in amplitude of no more than plus or minus 3 dB. However, one cannot determine from this information how smooth the variations are, nor in what parts of the spectrum they occur. Note that commonly made statements such as "20 Hz–20 kHz" are meaningless without a decibel measure of tolerance. Directional microphones' frequency response varies greatly with distance from the sound source, and with the geometry of the sound source. IEC 60268-4 specifies that frequency response should be measured in plane progressive wave conditions (very far away from the source) but this is seldom practical. Close talking microphones may be measured with different sound sources and distances, but there is no standard and therefore no way to compare data from different models unless the measurement technique is described.

The self-noise or equivalent input noise level is the sound level that creates the same output voltage as the microphone does in the absence of sound. This represents the lowest point of the microphone's dynamic range, and is particularly important should you wish to record sounds that are quiet. The measure is often stated in dB(A), which is the equivalent loudness of the noise on a decibel scale frequency-weighted for how the ear hears, for example: "15 dBA SPL" (SPL means sound pressure level relative to 20 micropascals). The lower the number the better. Some microphone manufacturers state the noise level using ITU-R 468 noise weighting, which more accurately represents the way we hear noise, but gives a figure some 11–14 dB higher. A quiet microphone typically measures 20 dBA SPL or 32 dB SPL 468-weighted. Very quiet microphones have existed for years for special applications, such the Brüel & Kjaer 4179, with a noise level around 0 dB SPL. Recently some microphones with low noise specifications have been introduced in the studio/entertainment market, such as models from Neumann and Røde that advertise noise levels between 5–7 dBA. Typically this is achieved by altering the frequency response of the capsule and electronics to result in lower noise within the A-weighting curve while broadband noise may be increased.

The maximum SPL the microphone can accept is measured for particular values of total harmonic distortion (THD), typically 0.5%. This amount of distortion is generally inaudible,[citation needed] so one can safely use the microphone at this SPL without harming the recording. Example: "142 dB SPL peak (at 0.5% THD)". The higher the value, the better, although microphones with a very high maximum SPL also have a higher self-noise.

The clipping level is an important indicator of maximum usable level, as the 1% THD figure usually quoted under max SPL is really a very mild level of distortion, quite inaudible especially on brief high peaks. Clipping is much more audible. For some microphones the clipping level may be much higher than the max SPL.

The dynamic range of a microphone is the difference in SPL between the noise floor and the maximum SPL. If stated on its own, for example "120 dB", it conveys significantly less information than having the self-noise and maximum SPL figures individually.

Sensitivity indicates how well the microphone converts acoustic pressure to output voltage. A high sensitivity microphone creates more voltage and so needs less amplification at the mixer or recording device. This is a practical concern but is not directly an indication of the microphone's quality, and in fact the term sensitivity is something of a misnomer, "transduction gain" being perhaps more meaningful, (or just "output level") because true sensitivity is generally set by the noise floor, and too much "sensitivity" in terms of output level compromises the clipping level. There are two common measures. The (preferred) international standard is made in millivolts per pascal at 1 kHz. A higher value indicates greater sensitivity. The older American method is referred to a 1 V/Pa standard and measured in plain decibels, resulting in a negative value. Again, a higher value indicates greater sensitivity, so −60  dB is more sensitive than −70 dB.

Measurement microphones[edit]

Some microphones are intended for testing speakers, measuring noise levels and otherwise quantifying an acoustic experience. These are calibrated transducers and are usually supplied with a calibration certificate that states absolute sensitivity against frequency. The quality of measurement microphones is often referred to using the designations "Class 1," "Type 2" etc., which are references not to microphone specifications but to sound level meters.[41] A more comprehensive standard[42] for the description of measurement microphone performance was recently adopted.

Measurement microphones are generally scalar sensors of pressure; they exhibit an omnidirectional response, limited only by the scattering profile of their physical dimensions. Sound intensity or sound power measurements require pressure-gradient measurements, which are typically made using arrays of at least two microphones, or with hot-wire anemometers.

Microphone calibration[edit]

To take a scientific measurement with a microphone, its precise sensitivity must be known (in volts per pascal). Since this may change over the lifetime of the device, it is necessary to regularly calibrate measurement microphones. This service is offered by some microphone manufacturers and by independent certified testing labs. All microphone calibration is ultimately traceable to primary standards at a national measurement institute such as NPL in the UK, PTB in Germany and NIST in the United States, which most commonly calibrate using the reciprocity primary standard. Measurement microphones calibrated using this method can then be used to calibrate other microphones using comparison calibration techniques.

Depending on the application, measurement microphones must be tested periodically (every year or several months, typically) and after any potentially damaging event, such as being dropped (most such microphones come in foam-padded cases to reduce this risk) or exposed to sounds beyond the acceptable level.

Microphone array and array microphones[edit]

Main article: Microphone array

A microphone array is any number of microphones operating in tandem. There are many applications:

Typically, an array is made up of omnidirectional microphones distributed about the perimeter of a space, linked to a computer that records and interprets the results into a coherent form.

Microphone windscreens[edit]

Windscreens[note 1] are used to protect microphones that would otherwise be buffeted by wind or vocal plosives from consonants such as "P", "B", etc. Most microphones have an integral windscreen built around the microphone diaphragm. A screen of plastic, wire mesh or a metal cage is held at a distance from the microphone diaphragm, to shield it. This cage provides a first line of defense against the mechanical impact of objects or wind. Some microphones, such as the Shure SM58, may have an additional layer of foam inside the cage to further enhance the protective properties of the shield. One disadvantage of all windscreen types is that the microphone's high frequency response is attenuated by a small amount, depending on the density of the protective layer.

Beyond integral microphone windscreens, there are three broad classes of additional wind protection.

Microphone covers[edit]

Microphone with its cover removed.

Microphone covers are often made of soft open-cell polyester or polyurethane foam because of the inexpensive, disposable nature of the foam. Optional windscreens are often available from the manufacturer and third parties. One disadvantage of polyurethane foam microphone covers is that they can deteriorate over time. Windscreens also tend to collect dirt and moisture in their open cells and must be cleaned to prevent high frequency loss, bad odor and unhealthy conditions for the person using the microphone. On the other hand, a major advantage of concert vocalist windscreens is that one can quickly change to a clean windscreen between users, reducing the chance of transferring germs. Windscreens of various colors can be used to distinguish one microphone from another on a busy, active stage.

Pop filters[edit]

Pop filters or pop screens are used in controlled studio environments to minimize plosives when recording. A typical pop filter is composed of one or more layers of acoustically transparent gauze-like material, such as woven nylon (e.g., pantyhose) stretched over a circular frame and a clamp and a flexible mounting bracket to attach to the microphone stand. The pop shield is placed between the vocalist and the microphone. The closer a vocalist brings his or her lips to the microphone, the greater the requirement for a pop filter. Singers can be trained either to soften their plosives or direct the air blast away from the microphone, in which cases they do not need a pop filter.

Pop filters also keep spittle off the microphone. Most[which?] condenser microphones can be damaged by spittle.


Blimps (also known as Zeppelins) are large, hollow windscreens used to surround microphones for outdoor location audio, such as nature recording, electronic news gathering, and for film and video shoots. They can cut wind noise by as much as 25 dB, especially low-frequency noise. The blimp is essentially a hollow cage or basket with acoustically transparent material stretched over the outer frame. The blimp works by creating a volume of still air around the microphone. The microphone is often further isolated from the blimp by an elastic suspension inside the basket. This reduces wind vibrations and handling noise transmitted from the cage. To extend the range of wind speed conditions in which the blimp remains effective, many have the option of a secondary cover over the outer shell. This is usually an acoustically transparent, synthetic fur material with long, soft hairs. Common and slang names for this include "dead cat" or "windmuff". The hairs deaden the noise caused by the shock of wind hitting the blimp. A synthetic fur cover can reduce wind noise by an additional 10 dB.[43]

See also[edit]


  1. ^ A microphone windscreen is sometimes called a wind gag, or dead cat or yeti.


  1. ^ Zimmer, Ben (29 July 2010). "How Should 'Microphone' be Abbreviated?". The New York Times. Retrieved 10 September 2010. 
  2. ^ Montgomery, Henry 1959 Amplification and High Fidelity in the Greek Theater. The Classic Journal
  3. ^ McVeigh, Daniel P 2000. An Early History of the Telephone: 1664–1866: Robert Hooke's Acoustic Experiments and Acoustic Inventions
  4. ^ MacLeod, Elizabeth 1999 Alexander Graham Bell: an inventive life. Kids Can Press, Toronto
  5. ^ Paul J. Nahin (2002). Oliver Heaviside: The Life, Work, and Times of an Electrical Genius of the Victorian Age. JHU Press. p. 67. 
  6. ^ Bob Estreich. "David Edward Hughes". 
  7. ^ a b Huurdeman, Anton (2003). The Worldwide History of Telecommunications. John Wiley & Sons. 
  8. ^ "David Hughes". Retrieved 2012-12-17. 
  9. ^ a b "A brief history of microphones". Retrieved 2012-12-17. 
  10. ^ "David Edward Hughes: Concertinist and Inventor". Retrieved 2012-12-17. 
  11. ^ Television International magazine article – Lee De Forest – (1873–1961). Retrieved 12-04-2013
  12. ^ Fagen, M.D. A History of Engineering and Science in the Bell System: The Early Years (1875–1925). New York: Bell Telephone Laboratories, 1975
  13. ^ Hennessy, Brian 2005 The Emergence of Broadcasting in Britain Devon Southerleigh
  14. ^ Robjohns, Hugh 2001 A Brief History of Microphones. Microphone Data Book
  15. ^ "1931 Harry F. Olson and Les Anderson, RCA Model 44 Ribbon Microphone". Mix Magazine. Sep 1, 2006. Retrieved 10 April 2013. 
  16. ^ "History – The evolution of an audio revolution". Shure Americas. Retrieved 13 April 2013. 
  17. ^ "Bell Laboratories and The Development of Electrical Recording". Stokowski.org (Leopold Stokowski site). 
  18. ^ Institute BV Amsterdam, SAE. "Microphones". Practical Creative Media Education. Retrieved 2014-03-07. 
  19. ^ Sessler, G.M.; West, J.E. (1962). "Self-biased condenser microphone with high capacitance". Journal of the Acoustical Society of America 34 (11): 1787–1788. doi:10.1121/1.1909130. 
  20. ^ [1][dead link]
  21. ^ "AKG D 112 – Large-diaphragm dynamic microphone for bass instruments"
  22. ^ "Local firms strum the chords of real music innovation". Mass High Tech: the Journal of New England Technology. February 8, 2008. 
  23. ^ "Boudet's Microphone". Machine-History.com. 
  24. ^ Paritsky, Alexander; Kots, A. (1997). "Fiber optic microphone as a realization of fiber optic positioning sensors". Proc. of International Society for Optical Engineering (SPIE) 3110: 408–409. 
  25. ^ US patent 6462808, Alexander Paritsky and Alexander Kots, "Small optical microphone/sensor", issued 2002-10-08 
  26. ^ "Case Study: Can You Hear Me Now?". rt image. Valley Forge Publishing. pp. 30–31. Retrieved 2009-08-23. 
  27. ^ "MEMS Microphone Will Be Hurt by Downturn in Smartphone Market". Seeking Alpha. Retrieved 2009-08-23. 
  28. ^ "OMRON to Launch Mass-production and Supply of MEMS Acoustic Sensor Chip -World's first MEMS sensor capable of detecting the lower limit of human audible frequencies-". Retrieved 2009-11-24. 
  29. ^ Bartlett, Bruce. "How A Cardioid Microphone Works". Retrieved 8/11/2008.  Check date values in: |accessdate= (help)
  30. ^ History & Development of Microphone. Lloyd Microphone Classics.
  31. ^ Proximity Effect. Geoff Martin, Introduction to Sound Recording.
  32. ^ "History – The evolution of an audio revolution". Shure. Retrieved 2013-07-30. 
  33. ^ Dave Berners (December 2005). "Ask the Doctors: The Physics of Mid-Side (MS) Miking". Universal Audio WebZine. Universal Audio. Retrieved 2013-07-30. 
  34. ^ "Directional Patterns of Microphones". Retrieved 2013-07-30. 
  35. ^ (US 4361736 )
  36. ^ Crown Audio. Tech Made Simple. The Crown Differoid Microphone[dead link]
  37. ^ a b International Standard IEC 60268-4
  38. ^ Eargle, John; Chris Foreman (2002). Audio Engineering for Sound Reinforcement. Milwaukee: Hal Leonard Corporation. p. 66. ISBN 0-634-04355-2. 
  39. ^ [2][dead link]
  40. ^ Robertson, A. E.: "Microphones" Illiffe Press for BBC, 1951–1963
  41. ^ IEC Standard 61672 and ANSI S1.4
  42. ^ IEC 61094
  43. ^ Full Windshield Kits. Rycote Microphones. Retrieved on May 3, 2010.

External links[edit]

Original courtesy of Wikipedia: http://en.wikipedia.org/wiki/Microphone — Please support Wikipedia.
This page uses Creative Commons Licensed content from Wikipedia. A portion of the proceeds from advertising on Digplanet goes to supporting Wikipedia.
1000000 videos foundNext > 

[Microphone REVIEWS] The Best Mic for Your Videos (Audio Tutorial)

In this microphone reviews edition, (http://www.jameswedmore.com/choose-best-microphone-videos/), we will take a closer look at FOUR of the most common micro...

Slaughterhouse "Microphone" Director's Cut / Album In Stores & Online Now

Slaughterhouse "Microphone" Director's Cut / Album In Stores & Online Now.

Best Microphone for Recording - YouTube, Radio & Podcasting

http://mrc.fm/sl150 I'm often asked what is the best microphone for recording vocals for YouTube, radio shows or podcasting. I test the Editors Keys SL150 Co...


Join me, Felix and Pomby in today's CREATIVERSE Video which is a game like minecraft ... but ... NEW and maybe better? Tell me what you think in the comments and leave a like if you'd like...

How to make your own microphone Pop Filter

I NEED YOUR HELP! Become MORE than a SUBSCRIBER!, Become part of the TechErtainment Elite and BE A PATRON TODAY and get Bonuses, Perks and Rewards. http://ww...

[MV HD] Microphone - Thu Thủy [Official]

microphone thu thuy,micrphone thu thuy microphone Lyrics: Microphone - Thu Thủy Đóng góp: Minh Trần Là thế đó, cứ mỗi sớm nhớ anh không nguôi Ngày ngày em ch...

USB Microphone Comparison

In this video we compare five popular, large diaphragm condenser USB microphones. To read more about microphones, check out the Microphones section on our bl...

Blue Snowball VS Blue Yeti Microphone (Review / Comparison)

Hey guys, today I compare the two common microphones used for commentaries on YouTube, the Blue Snowball and the Blue Yeti. I always get asked what I used to...

Home Recording Studio Advice: Buying your first microphone (a pro's perspective)

http://recordingbootcamp.com/ http://ronansrecordingshow.com/ Ronan Chris Murphy shares a professional perspective on choosing the right microphone for your ...

98º - Microphone (Lyric Video)

Music video by 98º performing Microphone. 2013 Entertainment One U.S., LP.

1000000 videos foundNext > 

10316186 news items

cinema5D news

cinema5D news
Thu, 27 Nov 2014 07:22:30 -0800

Here's an interesting tool that some filmmakers struggling with audio may like. Mikme is a wireless recording microphone, offering 24bit 96kHz audio at the touch of one button. Check out their Kickstarter campaign in the video below: ...


Mon, 24 Nov 2014 14:08:12 -0800

The folks behind the Mikme microphone are aiming to make recording inspired moments of creativity as easy as possible, whenever and wherever you happen to be when the muse strikes. Though you can make use of the microphone on the ubiquitous ...

Palm Beach Post

Palm Beach Post
Tue, 25 Nov 2014 05:32:43 -0800

The lead singer of an up-and-coming Argentinian rock band died over the weekend after being electrocuted on stage. According to multiple Spanish-language reports, Agustin Briolini, lead singer of the band Krebs, was doing a sound check prior to a show ...
Discover Magazine
Wed, 26 Nov 2014 07:45:00 -0800

More than 130 years after Thomas Edison shouted the song to his tinfoil phonograph, making the first human voice recording, researchers from MIT, Microsoft and Adobe recorded the rhyme using the world's first “visual microphone” — an empty bag of ...
Wed, 26 Nov 2014 13:11:15 -0800

Here we are, 20 years after the release of the original MXL 2001 microphone, and the company has maintained its place in the budget microphone game, while making some big moves toward the high-end. Its recent tube mics—Genesis, the Genesis II, and ...


Fri, 21 Nov 2014 10:04:15 -0800

Before the Maple Leafs were blown out by Nashville on Tuesday night, the microphone at the Air Canada Centre kept cutting out during the Star-Spangled Banner. So the fans in attendance decided to offer a helping hand and finish the song as a group.
Ubergizmo (blog)
Tue, 25 Nov 2014 14:52:30 -0800

When it comes to home or mobile recording, there are plenty of options available to musicians. Heck, worst comes to worst they can always rely on the default microphone found on their phones or tablets. Well if you'd rather have better quality music ...

Live Design

Live Design
Tue, 25 Nov 2014 10:56:15 -0800

When queried about those E6i attributes that make the microphone so well suited to her work, Zuleikha described both the microphone's audio characteristics and its fit. “I love the fact that my Countryman mic is so easy to work with. I never experience ...

Oops, we seem to be having trouble contacting Twitter

Support Wikipedia

A portion of the proceeds from advertising on Digplanet goes to supporting Wikipedia. Please add your support for Wikipedia!

Searchlight Group

Digplanet also receives support from Searchlight Group. Visit Searchlight