digplanet beta 1: Athena
Share digplanet:


Applied sciences






















One complete cycle of a four-cylinder, four-stroke engine. The volume displaced is marked in red.

Engine displacement is the volume swept by all the pistons inside the cylinders of a reciprocating engine in a single movement from top dead centre (TDC) to bottom dead centre (BDC). It is commonly specified in cubic centimetres (cc or cm3), litres (l), or (mainly in North America) cubic inches (CID). Engine displacement does not include the total volume of the combustion chamber.


Engine displacement is determined from the bore and stroke of an engine's cylinders. The bore is the diameter of the circular chambers cut into the cylinder block.

 \mbox{displacement} = {\pi\over 4} \times \mbox{bore}^2 \times \mbox{stroke} \times \mbox{number of cylinders}

Or in decimal form:

 \mbox{displacement} = \mbox{bore}^2 \times 0.7854 \times \mbox{stroke} \times \mbox{number of cylinders}

Examples: The 427 Chevy bore is 4.312 in, and the stroke is 3.65 in, therefore the displacement for this eight-cylinder engine is:

3.1416/4 × (4.312 in)2 × 3.65 in × 8 = 426.4 cu in


(4.312 in)2 × 0.7854 × 3.65 in × 8 = 426.4 cu in

If the bore is 10 cm and the stroke is 5 cm with four cylinders, the calculation is:

3.1416/4 × (10 cm)2 × 5 cm × 4 = 1,570 cc = 1.57 liters

Units of measure[edit]

In the United States, the cubic inch was the commonly used unit of measurement until the 1980s by the manufacturers to express the displacement of engines for cars, trucks, etc. (e.g., the "426" in 426 Hemi refers to 426 cubic inches displaced). It is still used for this purpose in the context of the classic-car hobby, auto racing, and so forth.[citation needed]

The automotive industry nowadays uses the International System of Units / le Système international d'unités (SI), a modern metric system for this purpose worldwide (e.g. 6.1 litre Hemi). However, in markets accustomed to cubic inches, the actual displacement measurements of an engine are still given by many manufacturers in these units, usually along with metric value; e.g. the 6.1-litre Hemi's published displacement is 370.0 CID/6,059 cc.[1][2][3][4] Some examples of common CID-to-litre conversions are given below. Note that nominal sizes are not always precisely equal to actual sizes. This principle is frequently seen in engineering, tool standardization, etc. (for ease of use) and in marketing (when a big round number sounds more impressive, is more memorable, etc.).

make (± division) cubic inch displacement (CID)
- (actual) (nearest 1)
cubic inch displacement (CID)
- (nominal)
International System of Units (SI)
- (actual) (nearest 0.01)
International System of Units (SI)
- (nominal)
Honda, Kawasaki, others something close to 61 CID N/A (not marketed in CID) [something close to SI nominal] 1000 cc (= 1.0 litre)
Honda, Kawasaki, others something close to 98 CID N/A (not marketed in CID) [something close to SI nominal] 1600 cc (= 1.6-litre)
Honda, Kawasaki, others; Ford something close to 122 CID N/A (not marketed in CID) [something close to SI nominal] 2000 cc (= 2.0-litre)
GM (Pontiac, Buick, Oldsmobile, GMC, others) 151 CID N/A (not marketed in CID) [something close to SI nominal] 2.5-litre
Toyota, Ford, Chrysler, others something close to 183 CID N/A (not marketed in CID) [something close to SI nominal] 3.0-litre
AMC, Jeep, Chrysler (I6) 241.573 CID 242 CID 3,959 cc 4.0-litre
Ford something close to 244 CID N/A (not marketed in CID) [something close to SI nominal] 4.0-litre
Ford (Ford, Mercury), GM (Chevrolet, GMC) [something close to CID nominal] 250 CID 4.10-litre 4.1-litre
AMC, Jeep, International Harvester [something close to CID nominal] 258 CID 4.22-litre 4.2-litre
GM (Chevrolet, GMC, Oldsmobile) [something close to CID nominal] 262 CID 4.33-litre 4.3-litre
Ford (Ford, Mercury) [something close to CID nominal] 289 CID 4.74-litre N/A (not marketed in SI)
Ford (Ford trucks and vans) [something close to CID nominal] 300 CID 4.92-litre 4.9-litre
GM (Pontiac) [something close to CID nominal] 301 CID 4.9-litre N/A (not marketed in SI)
Ford, GM (Chevrolet) [something close to CID nominal] 302 CID (302 Windsor, 302 Cleveland, Chevrolet 302) 4.95-litre 5.0-litre
GM (Oldsmobile) 303 CID
AMC, Jeep, International Harvester [something close to CID nominal] 304 CID 4.98-litre 5.0-litre
GM (Chevrolet, Pontiac, Oldsmobile, Buick) [something close to CID nominal] 305 CID 5.0-litre N/A (not marketed in S/I)
GM (Chevrolet; Buick) 307 CID 307 CID 5.03-litre N/A (not marketed in SI)
GM (Oldsmobile) 307 CID N/A (not marketed in CID) 5.03-litre 5.0-litre
Chrysler (Chrysler, Dodge, Plymouth) [something close to CID nominal] 318 CID 5.21-litre 5.2-litre
AMC, GM (Chevrolet) 327 CID 327 CID 5.36-litre N/A (not marketed in SI)
GM (Oldsmobile) 330 CID
Buick, Chrysler (Chrysler, Dodge, Plymouth) [something close to CID nominal] 340 CID 5.57-litre N/A (not marketed in SI)
GM (GMC, Chevrolet, Buick, Oldsmobile, Pontiac, others) [something close to CID nominal] 350 CID 5.74-litre 5.7-litre
Ford (Ford, Mercury) [something close to CID nominal] 351 CID (Cleveland or Windsor) 5.75-litre 5.8-litre
AMC, Chrysler (Chrysler, Dodge, Plymouth) [something close to CID nominal] 360 CID 5.90-litre 5.9-litre
Chrysler (Chrysler, Dodge, Plymouth) [something close to CID nominal] 383 CID 6.28-litre N/A (not marketed in SI)
GM (Pontiac) [something close to CID nominal] 389 CID 6.5-litre N/A (not marketed in SI)
AMC, Ford, GM (Cadillac) [something close to CID nominal] 390 CID 6.39-litre N/A (not marketed in SI)
GM (Oldsmobile) 394 CID
GM (Chevrolet) [sometimes 396 CID, sometimes 402 CID] 396 CID 6.49-litre N/A (not marketed in SI)
GM (Chevrolet, Pontiac, Oldsmobile) [something close to CID nominal] 400 CID 6.55-litre N/A (not marketed in SI)
GM (Buick) 401 CID
GM (Chevrolet) [something close to CID nominal] 409 CID 6.70-litre N/A (not marketed in SI)
GM (Pontiac) [something close to CID nominal] 421 CID 6.90-litre N/A (not marketed in SI)
GM (Oldsmobile) 425 CID
Chrysler (Chrysler, Dodge, Plymouth) [something close to CID nominal] 426 CID (Wedge or Hemi) 6.98-litre 7.0-litre
Ford (Ford, Mercury) [something close to CID nominal] 427 CID 7.00-litre 7.0-litre
GM (Pontiac),Ford (Ford, Mercury) [something close to CID nominal] 428 CID 7.01-litre 7.0-litre
Ford (Ford, Mercury) [something close to CID nominal] 429 CID 7.03-litre 7.0-litre
Chrysler (Chrysler, Dodge, Plymouth) [something close to CID nominal] 440 CID 7.21-litre 7.2-litre
GM (GMC, Chevrolet) [something close to CID nominal] 454 CID 7.44-litre 7.4-litre
GM (Buick, Oldsmobile, Pontiac) [something close to CID nominal] 455 CID 7.46-litre N/A (not marketed in SI)
Ford (Ford [trucks and vans]; Lincoln [cars]) [something close to CID nominal] 460 CID 7.54-litre 7.5-litre
GM (Cadillac) [something close to CID nominal] 472 CID 7.73-litre 7.7-litre
GM (Cadillac) [something close to CID nominal] 500 CID 8.19-litre 8.2-litre
Chrysler (Dodge) 506.5 CID 505 CID 8285 cc 8.3-litre
Chrysler (Dodge) 509.8 CID 510 CID 8354 cc 8.4-litre
GM (GM Performance Parts) [something close to CID nominal] 572 CID 9373 cc 9.4-litre

Governmental regulations[edit]

Taxation of automobiles is sometimes based on engine displacement, rather than power output, fuel economy, or emissions. Displacement is a basic fundamental of engine design, whereas power output depends a great deal on other factors, particularly on how the car manufacturer has tuned the engine from new. This has encouraged the development of other methods to increase engine power, such as variable valve timing and turbochargers.

There are four major regulatory constraints for automobiles: the European, British, Japanese, and American. The method used in some European countries, and which predates the EU, has a level of taxation for engines over 1.0 litre, and another at the level of about 1.6 litres. The British system of taxation depends upon vehicle emissions for cars registered after 1 March 2001, but for cars registered before this date, it depends on engine size. Cars under 1549 cc qualify for a cheaper rate of tax.[5]

The Japanese method is similar to the European taxation by classes of displacement, plus a vehicle weight tax.

The United States does not tax a vehicle based on the displacement of the engine (this is also true in Canada, Australia, and New Zealand). Engine displacement is important in determining whether or not smaller vehicles need to be registered with the state and whether or not a license is required to operate such a vehicle. A common threshold is 50cc.

In the Netherlands[6] and in Sweden, road tax is based on vehicle weight. However, Swedish cars registered in 2008, or later, are taxed based on carbon dioxide emissions.[citation needed]

Displacement is also used to distinguish categories of (heavier) and lighter motorbikes with respect to driving licence and insurance requirements. In France and some other EU countries, mopeds of less than 50 cm3 displacement (and usually with a two-stroke engine), can be driven with minimum qualifications (previously, they could be driven by any person over 14). This led to all light motorbikes having a displacement of about 49.9 cm3. Some people tuned the engine by increasing the cylinder bore, increasing displacement; such mopeds cannot be driven legally on public roads since they do no longer conform to the original specifications and may go faster than 45 km/h.

Wankel engines, due to the amount of power and emissions they create for their displacement, are generally taxed as 1.5 times their stated physical displacement (1.3 litres becomes effectively 2.0, 2.0 becomes effectively 3.0), although actual power outputs are far greater (the 1.3-litre 13B can produce power comparable to a 3.0 V6 engine, and the 2.0-litre 20B can produce power comparable to a 4.0 V8 engine).[citation needed] As such, racing regulations actually use a much higher conversion factor.

Automotive model names[edit]

In the automotive industry, engine displacement is frequently encoded in the auto manufacturer's model names. For instance, Nissan's Teana 350JM is a car with a 3,498 cc (213.5 cu in displacement (CID) engine). Motorcycles are often labeled similarly. However, this can be misleading. For instance, the BMW 335i only has a 3.0-litre (twin-turbocharged) engine.[7] Lexus hybrid vehicles (h) are marked higher than its engine size to signify the extra power from its auxiliary systems. (Examples: RX450h has a 3.5 L engine, LS600h has a 5.0 L engine)

See also[edit]


  1. ^ "2008 Dodge Charger – specs & upgrades". Chrysler. Retrieved 2008-05-02. 
  2. ^ "Ford Vehicles: get specifications F-150". Ford Motor Company. Retrieved 2008-04-25. "Engine type: 5.4L Triton SOHC 24-valve V8... Displacement (cu. in.): 330 CID" 
  3. ^ "Chevrolet 2008 Silverado Pickup Truck - specifications (under engine 'tab')". GM. Retrieved 2008-04-25. "Engine: Vortec 5.3L Aluminum-Block V8...Displacement (cu. in.): 325" 
  4. ^ "Dodge specifications". Chrysler LLC. Retrieved 2008-04-25. "Powertrain: Engine - Displacement - Cubic Inches: 345.0" 
  5. ^ The Cost of Vehicle Tax for Cars, Motorcycles, Light Goods Vehicles and Trade Licences." Direct.gov.uk
  6. ^ Road tax also based on region and fuel type (petrol / CNG, LPG, Diesel, or other (electric/hybrid/H2))
  7. ^ https://www.press.bmwgroup.com/pressclub/p/pcgl/pressDetail.html?outputChannelId=6&id=T0084262EN&left_menu_item=node__2229

Original courtesy of Wikipedia: http://en.wikipedia.org/wiki/Engine_displacement — Please support Wikipedia.
This page uses Creative Commons Licensed content from Wikipedia. A portion of the proceeds from advertising on Digplanet goes to supporting Wikipedia.
174953 videos foundNext > 

3D Engine Displacement Video - English units

A quick engine displacement lesson in 3D form. If you are a teacher using this in or for your class, please message me, I'd love to know if it was effective!...

Toby's Kitchen: What is engine displacement?

This is how you calculate your engine cc's and why when you bore your bike out you don't exagerate what cc's your bike is or remodel your bike's model number.

Engine compression ratio and displacement calculation

11th part of the Oldsmobile 455 marine engine build. The worked over cylinder heads are looked at in this video. Timing marks, compression and displacement a...

engine displacement.wmv

CC, engine displacement.

How Calculate Compression-Ratio, Engine Displacement + more!

Become an expert engine builder. Calculate displacement, compression ratio, compression height, cylinder head power potential and much more! Save your compre...

how to calculate engine displacement from ci to liters

if you have been through high school or middle school this should seem familiar units to metric conversions using formulas. Its not hard but one of the dumbe...

Prt 1 - Source Engine Displacement Caves Tutorial

The very first Tech Talk with TorQue[MoD] video tutorial on creating caves using displacement maps in Hammer for Source Engine games.

Operating on the Testing Bench(Engine Displacement : 80cc)

This image has been derived from NITTO MFG. WORKS' URL http://www.nitto-mfg.com/ (

Prt 2B - Source Engine Displacement Caves Tutorial

Part 2 (B) of theTech Talk with TorQue[MoD] video tutorial on creating caves using displacement maps in Hammer for Source Engine games.

My Homemade LTD Stirling Engine (Displacement type) Part 1 of 2

My First Stirling Engine. I was very happy to see it work on the first try without any tunning. Running on heat from an electric range. Made mostly from a co...

174953 videos foundNext > 

86 news items

Bold Ride Blog (blog)

Bold Ride Blog (blog)
Mon, 28 Jul 2014 10:26:15 -0700

New for 1968 was a mandatory step-back on engine displacement – brought down to 3.0-liters – which was in line with contemporary Formula 1 engines. It sent Marsh to the market in search of a BRM V12. Unfortunately, it proved too expensive, so the ...
Chicago Tribune
Sun, 27 Jul 2014 17:56:15 -0700

Instead of offering licenses in just two size classes — one for cycles with an engine displacement of less than 150 cubic centimeters, like off-road bikes and scooters, and another for all other sizes — Illinois would add a third category for the ...
The Car Guide
Mon, 28 Jul 2014 09:48:44 -0700

In recent years, we've seen a downward trend among automakers, who are cutting back on engine displacement and using superchargers to compensate. As a result, performance is unaffected—or even increased—while fuel consumption is reduced.


Mon, 28 Jul 2014 03:18:45 -0700

The bike has a Twin Cam 96 Pushrod V-twin engine with 1584cc engine displacement. The bike's torque comes in at 92ft lbs and its bore/stroke ratio at 95.25 x 111.25mm. This 2008 model has 4.8-gallon fuel capacity. Clay's bike also has a forward facing ...
Chinadaily USA
Sun, 27 Jul 2014 17:00:00 -0700

To deal with the excessive number of government vehicles, the authorities should strictly stipulate the requirements to be met before an official is offered a government vehicle and strictly control the quantity, engine displacement and price of these ...


Mon, 28 Jul 2014 01:05:17 -0700

I mean you can say Honda Stunner or Hero Ignitor but then both those motorcycles fall in the 125cc engine displacement segment and are better looking as well. The Discover 150F on the other hand feels like just another product which has been introduced ...

Gas 2.0

Gas 2.0
Fri, 18 Jul 2014 12:52:30 -0700

The Cummins ETHOS engine began life as the 6.7 liter V-8 commonly found in many medium duty commercial trucks. Working in cooperation with the California Energy Commission, they cut engine displacement down to 4.5 liters, then realized they could go ...

Sports Car Illustrated

Sports Car Illustrated
Thu, 24 Jul 2014 16:03:45 -0700

The previous power density of 83 hp (61 kW) per litre engine displacement was increased to 117 hp (86 kW) (gain of around 40 percent). With its standard eight-speed Tiptronic S transmission, the Cayenne S accelerates from zero to 100 km/h in just 5.5 ...

Oops, we seem to be having trouble contacting Twitter

Talk About Engine displacement

You can talk about Engine displacement with people all over the world in our discussions.

Support Wikipedia

A portion of the proceeds from advertising on Digplanet goes to supporting Wikipedia. Please add your support for Wikipedia!