digplanet beta 1: Athena
Share digplanet:

Agriculture

Applied sciences

Arts

Belief

Business

Chronology

Culture

Education

Environment

Geography

Health

History

Humanities

Language

Law

Life

Mathematics

Nature

People

Politics

Science

Society

Technology

A 302/5.0L Ford cylinder head

In an internal combustion engine, the cylinder head (often informally abbreviated to just head) sits above the cylinders on top of the cylinder block. It closes in the top of the cylinder, forming the combustion chamber. This joint is sealed by a head gasket. In most engines, the head also provides space for the passages that feed air and fuel to the cylinder, and that allow the exhaust to escape. The head can also be a place to mount the valves, spark plugs, and fuel injectors.

Sidevalve engines[edit]

In a flathead or sidevalve engine, the mechanical parts of the valve train are all contained within the block, and the a 'poultice head' may be used that is essentially a simple metal plate bolted to the top of the block.

Keeping all moving parts within the block has an advantage for physically large engines in that the camshaft drive gear is small and so suffers less from the effects of thermal expansion in the cylinder block. With a chain drive to an overhead camshaft, the extra length of chain needed for an overhead cam design could give trouble from wear and slop in the chain without frequent maintenance.

Early sidevalve engines were in use at a time of simple fuel chemistry, low octane ratings and so required low compression ratios. This made their combustion chamber design less critical and there was less need to design their ports and airflow carefully.

One difficulty experienced at this time was that the low compression ratio also implied a low expansion ratio during the power stroke.[note 1] Exhaust gases were thus still hot, hotter than a contemporary engine, and this led to frequent trouble with burnt exhaust valves.

A major improvement to the sidevalve engine was the advent of Ricardo's turbulent head design. This reduced the space within the combustion chamber and the ports, but by careful thought about the airflow paths within them it allowed a more efficient flow in and out of the chamber. Most importantly, it used turbulence within the chamber to thoroughly mix the fuel and air mixture. This, of itself, allowed the use of higher compression ratios and more efficient engine operation.

Despite common knowledge, the limit on sidevalve performance is not the gas flow through the valves, but rather the shape of the combustion chamber. With high speed engines and high compression, the limiting difficulty becomes that of achieving complete and efficient combustion, whist also avoiding the problems of unwanted pre-detonation. The shape of a sidevalve combustion chamber, being inevitably wider than the cylinder to reach the valve ports, conflicts with achieving both an ideal shape for combustion[note 2] and also the small volume (and low height) needed for high compression. Modern, efficient engines thus tend towards the pent roof or hemi designs, where the valves are brought close in to the centre of the space.

Where fuel quality is low and octane rating is poor, compression ratios will be restricted. In these cases, the sidevalve engine still has much to offer. Particularly in the case of the developed IOE engine for a market with poor fuels, engines such as Rolls-Royce B series or the Land-Rover use a complicated arrangement of inclined valves, a cylinder head line at an angle to the bore and corresponding angled pistons to provide a compact combustion chamber approaching the near-hemispherical ideal. Such engines remained in production into the 1990s, only being finally replaced when the fuels available 'in the field' became more likely to be diesel than petrol.

Detail[edit]

Internally, the cylinder head has passages called ports or tracts for the fuel/air mixture to travel to the inlet valves from the intake manifold, and for exhaust gases to travel from the exhaust valves to the exhaust manifold. In a water-cooled engine, the cylinder head also contains integral ducts and passages for the engines' coolant - usually a mixture of water and antifreeze - to facilitate the transfer of excess heat away from the head, and therefore the engine in general.

In the overhead valve (OHV) design, the cylinder head contains the poppet valves and the spark plugs, along with tracts or 'ports' for the inlet and exhaust gases. The operation of the valves is initiated by the engine's camshaft, which is sited within the cylinder block, and its moment of operation is transmitted to the valves pushrods, and then rocker arms mounted on a rocker shaft - the rocker arms and shaft also being located within the cylinder head.

In the overhead camshaft (OHC) design, the cylinder head contains the valves, spark plugs and inlet/exhaust tracts just like the OHV engine, but the camshaft is now also contained within the cylinder head. The camshaft may be seated centrally between each offset row of inlet and exhaust valves, and still also utilizing rocker arms (but without any pushrods), or the camshaft may be seated directly above the valves eliminating the rocker arms and utilizing 'bucket' tappets.

Implementation[edit]

The number of cylinder heads in an engine is a function of the engine configuration. Almost all inline (straight) engines today use a single cylinder head that serves all the cylinders. A V (or Vee) engine has two cylinder heads, one for each cylinder bank of the 'V'. For a few compact 'narrow angle' V engines, such as the Volkswagen VR6, the angle between the cylinder banks is so narrow that it uses a single head spanning the two banks. A flat engine (basically a V engine, where the angle between the cylinder banks is now 180°) has two heads. Most radial engines have one head for each cylinder, although this is usually of the monobloc form wherein the head is made as an integral part of the cylinder. This is also common for motorcycles, and such head/cylinder components are referred-to as barrels.

Some engines, particularly medium- and large-capacity diesel engines built for industrial, marine, power generation, and heavy traction purposes (large trucks, locomotives, heavy equipment etc.) have individual cylinder heads for each cylinder. This reduces repair costs as a single failed head on a single cylinder can be changed instead of a larger, much more expensive unit fitting all the cylinders. Such a design also allows engine manufacturers to easily produce a 'family' of engines of different layouts and/or cylinder numbers without requiring new cylinder head designs.

The design of the cylinder head is key to the performance and efficiency of the internal combustion engine, as the shape of the combustion chamber, inlet passages and ports (and to a lesser extent the exhaust) determines a major portion of the volumetric efficiency and compression ratio of the engine.

Automotive 4-Stroke Engine Head Designs - Valve and Camshaft Configurations
Common Names Camshaft Intake Valves Exhaust Valves Notes
Dual Overhead Cam
DOHC
Head Head Head Allows optimum positioning of the valves for a crossflow cylinder head.
Double camshafts are used to allow direct actuation of well-placed valves, without rockers.
Widespread in modern car design
Overhead Cam
OHC
Head Head Head Widely used for cars in recent decades, but increasingly superseded by DOHC.
Overhead Valve
OHV, I-Head, Pushrod
Block Head Head Still used in big V8 pushrod engines
Needs pushrods and rockers to actuate valves
Sidevalve
Flathead, L-Head, T-Head
Block Block Block Once universal, now obsolete
Simplest possible configuration
Cams operate directly on the valves
Inlet-Over-Exhaust
IOE, F-Head
Block Head Block Always uncommon, obsolete for decades

Gallery[edit]

See also[edit]

Notes[edit]

  1. ^ The work done on the piston during the expansion stroke is limited by how much stroke there is in which to achieve it.
  2. ^ At the simplest level, a sphere approaches the ideal shape for combustion as it has the shortest paths across which to propagate the flame front. As one wall of this is the moving piston, hemispheres are more commonly chosen

References[edit]

External links[edit]



Original courtesy of Wikipedia: http://en.wikipedia.org/wiki/Cylinder_head — Please support Wikipedia.
This page uses Creative Commons Licensed content from Wikipedia. A portion of the proceeds from advertising on Digplanet goes to supporting Wikipedia.
1000000 videos foundNext > 

Cylinder Head 204 - Porting & Polishing

This is a first-generation 1992 1.6L Hyundai Elantra small-combustion-chamber head. Thats what it is. It's a J1 engine's cylinder head. In Cylinder Head 106 ...

How Cylinder Heads Work

This video details how some cylinders heads are made and the basic idea of how they all work. Understanding how they work is critical in diagnosing problems....

Cylinder Head 105 - Valve Job Basics

Valves not sealing? Valves not bent? This is how you fix that problem. In this video I outline the basic valve job procedure. Cleaning the valves, cleaning t...

How To Remove and Replace Valves in a Cylinder Head -EricTheCarGuy

If you need to remove a valve from a cylinder head either to replace the valve or replace the valve seals, this video will help you do that. You can also do ...

Cylinder head inspection for flatness / warping

Inspection of a 4 cylinder Saab 9-3 2.0l turbo cylinder head for flatness. The head uses a MLS (multi layer sheet) gasket so tolerance is only about 0.004". ...

Subaru Cylinder Head Removal

Subaru Master Mechanic, Mike Bauer, demonstrates, step-by-step, how to remove the cylinder heads from a Subaru 2.5L flat (boxer) engine from a 1999 Subaru Forester with automatic transmission...

How To Torque Cylinder Head Bolts - EricTheCarGuy

How To Torque Cylinder Head Bolts - EricTheCarGuy http://www.ericthecarguy.com/ Well this was a fun one to make. I believe I covered everything but if you fe...

Cylinder Head 102 - Hydro Test Valves

If you noticed a drop in compression on one cylinder, and pouring a cap of oil through the spark plug holes didn't fix it, then it's likely you experienced a...

Cylinder Head 201 - Radius Cut Valve Job

This video covers the complete valve job process that your machinist might perform. If the 100 series videos didn't help you identify and correct a problem w...

Replace a Cylinder Head Gasket Yourself and do it RIGHT! Part 1

Thoroughly detailed video on replacing your head gasket on any vehicle- though a Toyota 2.2L is used in the example. Includes measuring warpage specification...

1000000 videos foundNext > 

221 news items

 
Popular Hot Rodding Magazine
Wed, 27 Aug 2014 03:18:45 -0700

To find the extra power, cylinder head modifications were a key consideration. Now, there is virtually no limit on how far you can go with a porting and modification program, but we were looking for practical increases with maximum results for the time ...

TechnologyTell

TechnologyTell
Wed, 27 Aug 2014 22:26:15 -0700

The cylinder head portion of the water jacket was designed with the intent of maximum combustion chamber cooling; reducing the required octane content in the fuel used which in turn allowed for higher compression ratios. The volume was kept to a ...
 
Jalopnik
Thu, 28 Aug 2014 13:45:02 -0700

Every single sign pointed towards busted head gaskets, but I just wanted to be sure before I started busting my knuckles trying to figure out exactly what "Uniformly tighten the nuts in several passes" entails when getting the cylinder head covers back on.

GTspirit

GTspirit
Fri, 29 Aug 2014 00:07:30 -0700

To help create the uprated V8, Ford implemented larger intake valves, larger exhaust valves, revised intake and exhaust camshafts, stiffer valve springs, a new cylinder head casting, Sinter forged connecting rods, redesigned piston tops and a ...
 
Popular Hot Rodding Magazine
Thu, 28 Aug 2014 03:52:30 -0700

Originally introduced in 1962 in a displacement of 221 ci, the Ford Windsor, with its 8.200-inch deck height and compact inline cylinder head arrangement, was a good thing in a very small and lightweight package. The original low-deck Windsor grew ...
 
All At Sea
Thu, 28 Aug 2014 18:07:30 -0700

Two: Wind back the four decompression posts, one on each cylinder head. (They resembled bolts and you backed them off with a wrench.) Three: And this is where it got interesting. Remove the forward decompression post altogether and pour neat gasoline ...

AftermarketNews.com (AMN)

AftermarketNews.com (AMN)
Fri, 29 Aug 2014 08:22:30 -0700

TEM, which specializes in head porting, flow bench, cylinder head research and development, has been in operation since 1997. “We are down. But we are not out,” Oliver said, adding that TEM has set up a temporary office at his wife's Coldwell Banker ...
 
Import Tuner Magazine
Thu, 28 Aug 2014 14:11:15 -0700

Unless you're prepared to go further into dissecting your engine, expect to pay a gratuitous amount of cash on a set of aftermarket camshafts, high compression pistons, and port and polished cylinder head. The Scion FR-S/Subaru BRZ, and Toyota 86 have ...
Loading

Oops, we seem to be having trouble contacting Twitter

Talk About Cylinder head

You can talk about Cylinder head with people all over the world in our discussions.

Support Wikipedia

A portion of the proceeds from advertising on Digplanet goes to supporting Wikipedia. Please add your support for Wikipedia!