digplanet beta 1: Athena
Share digplanet:

Agriculture

Applied sciences

Arts

Belief

Business

Chronology

Culture

Education

Environment

Geography

Health

History

Humanities

Language

Law

Life

Mathematics

Nature

People

Politics

Science

Society

Technology

For compression ratio in data compression, see data compression ratio.

The compression ratio of an internal-combustion engine or external combustion engine is a value that represents the ratio of the volume of its combustion chamber from its largest capacity to its smallest capacity. It is a fundamental specification for many common combustion engines.

In a piston engine, it is the ratio between the volume of the cylinder and combustion chamber when the piston is at the bottom of its stroke, and the volume of the combustion chamber when the piston is at the top of its stroke.[1]

For example, a cylinder and its combustion chamber with the piston at the bottom of its stroke may contain 1000 cc of air (900 cc in the cylinder plus 100 cc in the combustion chamber). When the piston has moved up to the top of its stroke inside the cylinder, and the remaining volume inside the head or combustion chamber has been reduced to 100 cc, then the compression ratio would be proportionally described as 1000:100, or with fractional reduction, a 10:1 compression ratio.

A high compression ratio is desirable because it allows an engine to extract more mechanical energy from a given mass of air-fuel mixture due to its higher thermal efficiency. This occurs because internal combustion engines are heat engines, and higher efficiency is created because higher compression ratios permit the same combustion temperature to be reached with less fuel, while giving a longer expansion cycle, creating more mechanical power output and lowering the exhaust temperature. It may be more helpful to think of it as an "expansion ratio", since more expansion reduces the temperature of the exhaust gases, and therefore the energy wasted to the atmosphere. Diesel engines actually have a higher peak combustion temperature than petrol engines, but the greater expansion means they reject less heat in their cooler exhaust.

Higher compression ratios will however make gasoline engines subject to engine knocking if lower octane-rated fuel is used, also known as detonation. This can reduce efficiency or damage the engine if knock sensors are not present to retard the timing. However, knock sensors have been a requirement of the OBD-II specification used in 1996 model year vehicles and newer.

On the other hand, Diesel engines operate on the principle of compression ignition, so that a fuel which resists autoignition will cause late ignition, which will also lead to engine knock.

Formula[edit]

The ratio is calculated by the following formula:

\mbox{CR} = \frac { \tfrac{\pi}{4} b^2 s + V_c } {V_c}, where
b\; = cylinder bore (diameter)
s\; = piston stroke length
V_c\; = clearance volume. It is the volume of the combustion chamber (including head gasket). This is the minimum volume of the space at the end of the compression stroke, i.e. when the piston reaches top dead center (TDC). Because of the complex shape of this space, it is usually measured directly rather than calculated.

Typical compression ratios[edit]

Gasoline (petrol) engine[edit]

The compression ratio in a gasoline or petrol-powered engine will usually not be much higher than 10:1 due to potential engine knocking (detonation) and not lower than 6:1. Some production automotive engines built for high performance from 1955–1972, used high-octane leaded gasoline or '5 star' to allow compression ratios as high as 13.0:1.

A technique used to prevent the onset of knock is the high "swirl" engine that forces the intake charge to adopt a very fast circular rotation in the cylinder during compression that provides quicker and more complete combustion. It is possible to manufacture gasoline engines with compression ratios of over 11:1 that can use 87 (MON + RON)/2 (octane rating) fuel with the addition of variable valve timing and knock sensors to delay ignition timing. Such engines may not produce their full rated power using 87 octane gasoline under all circumstances, due to the delayed ignition timing. Direct fuel injection, which can inject fuel only at the time of fuel ignition (similar to a diesel engine), is another recent development which also allows for higher compression ratios on gasoline engines.

The CR can be as high as 13.5:1 (2013 Ferrari LaFerrari) in engines with a 'ping' or 'knock' sensor and an electronic control unit. In 1981, Jaguar released a cylinder head that allowed up to 14:1 compression; but settled for 12.5:1 in production cars. The cylinder head design was known as the "May Fireball" head; it was developed by a Swiss engineer Michael May.

In 2012, Mazda released new petrol engines under the brand name SkyActiv with a 14:1 compression ratio (U.S. models have a 13:1 compression ratio to allow for 87 AKI octane), to be used in all Mazda vehicles by 2015.[2][3][4]

Petrol/gasoline engine with pressure-charging[edit]

In a turbocharged or supercharged gasoline engine, the CR is customarily built at 10.5:1 or lower. This is due to the turbocharger/supercharger already having compressed the fuel/air mixture considerably before it enters the cylinders.

Petrol/gasoline engine for racing[edit]

Motorcycle racing engines can use compression ratios as high as 14:1, and it is common to find motorcycles with compression ratios above 12.0:1 designed for 86 or 87 octane fuel. F1 engines come closer to 17:1, which is critical for maximizing volumetric/fuel efficiency at around 18000 RPM.

Ethanol and methanol engines[edit]

Ethanol and methanol can take significantly higher compression ratios than gasoline. Racing engines burning methanol and ethanol fuel often incorporate a CR of 14.5-16:1.

Gas-fueled engine[edit]

The CR may be higher in engines running exclusively on LPG or CNG, due to the higher octane rating of these fuels.

Diesel engine[edit]

There is no electrical sparking plug in an auto-ignition diesel engine; the heat of compression raises the temperature of the mixture to its auto-ignition point. The CR will customarily exceed 14:1 and ratios over 22:1 are common. The appropriate compression ratio depends on the design of the cylinder head. The figure is usually between 14:1 and 16:1 for direct injection engines, and between 18:1 and 23:1 for indirect injection

Kerosene engine[edit]

A compression ratio of 6.5 or lower is desired for operation on Kerosene. The petrol-paraffin engine version of the Ferguson TE20 tractor had a compression ratio of 4.5:1 for operation on tractor vaporising oil with an octane rating between 55 and 70.[5]

Fault finding and diagnosis[edit]

Measuring the compression pressure of an engine, with a pressure gauge connected to the spark plug opening, gives an indication of the engine's state and quality. There is, however, no formula to calculate compression ratio based on cylinder pressure.

If the nominal compression ratio of an engine is given, the pre-ignition cylinder pressure can be estimated using the following relationship:

p = p_0 \times \text{CR}^\gamma

where p_0\; is the cylinder pressure at bottom dead center which is usually at 1 atm, \text{CR} is the compression ratio, and \gamma\; is the specific heat ratio for the working fluid, which is about 1.4 for air, and 1.3 for methane-air mixture.

For example, if an engine running on gasoline has a compression ratio of 10:1, the cylinder pressure at top dead center is

 p_\text{TDC} = 1 \text{ bar} \times 10^{1.4} = 25.1 \text{ bar}

This figure, however, will also depend on cam (i.e. valve) timing. Generally, cylinder pressure for common automotive designs should at least equal 10 bar, or, roughly estimated in pounds per square inch (psi) as between 15 and 20 times the compression ratio, or in this case between 150 psi and 200 psi, depending on cam timing. Purpose-built racing engines, stationary engines etc. will return figures outside this range.

Factors including late intake valve closure (relatively speaking for camshaft profiles outside of typical production-car range, but not necessarily into the realm of competition engines) can produce a misleadingly low figure from this test. Excessive connecting rod clearance, combined with extremely high oil pump output (rare but not impossible) can sling enough oil to coat the cylinder walls with sufficient oil to facilitate reasonable piston ring sealing. In engines with compromised ring seals, this can artificially give a misleadingly high compression figure.

This phenomenon can actually be used to some slight advantage. If a compression test does give a low figure, and it has been determined it is not due to intake valve closure/camshaft characteristics, then one can differentiate between the cause being valve/seat seal issues and ring seal by squirting engine oil into the spark plug orifice, in a quantity sufficient to disperse across the piston crown and the circumference of the top ring land, and thereby affect the mentioned seal. If a second compression test is performed shortly thereafter, and the new reading is much higher, it would be the ring seal that is problematic, whereas if the compression test pressure observed remains low, it is a valve sealing (or more rarely head gasket, or breakthrough piston or, rarer still, cylinder-wall damage) issue.

If there is a significant (greater than 10%) difference between cylinders, that may be an indication that valves or cylinder head gaskets are leaking, piston rings are worn, or that the block is cracked.

If a problem is suspected, then a more comprehensive test using a leak-down tester can locate the leak.

Variable Compression Ratio (VCR) engines[edit]

Because cylinder-bore diameter, piston-stroke length and combustion-chamber volume are almost always constant, the compression ratio for a given engine is almost always constant, until engine wear takes its toll.

One exception is the experimental Saab Variable Compression engine (SVC). This engine, designed by Saab Automobile, uses a technique that dynamically alters the volume of the combustion chamber (Vc), which, via the above equation, changes the compression ratio (CR).

The Atkinson cycle engine was one of the first attempts at variable compression. Since the compression ratio is the ratio between dynamic and static volumes of the combustion chamber, the Atkinson cycle's method of increasing the length of the power stroke compared to the intake stroke ultimately altered the compression ratio at different stages of the cycle.

Dynamic compression ratio[edit]

The calculated compression ratio, as given above, presumes that the cylinder is sealed at the bottom of the stroke, and that the volume compressed is the actual volume.

However: intake valve closure (sealing the cylinder) always takes place after BDC, which may cause some of the intake charge to be compressed backwards out of the cylinder by the rising piston at very low speeds; only the percentage of the stroke after intake valve closure is compressed. Intake port tuning and scavenging may allow a greater mass of charge (at a higher than atmospheric pressure) to be trapped in the cylinder than the static volume would suggest ( This "corrected" compression ratio is commonly called the "dynamic compression ratio".

This ratio is higher with more conservative (i.e., earlier, soon after BDC) intake cam timing, and lower with more radical (i.e., later, long after BDC) intake cam timing, but always lower than the static or "nominal" compression ratio.

The actual position of the piston can be determined by trigonometry, using the stroke length and the connecting rod length (measured between centers). The absolute cylinder pressure is the result of an exponent of the dynamic compression ratio. This exponent is a polytropic value for the ratio of variable heats for air and similar gases at the temperatures present. This compensates for the temperature rise caused by compression, as well as heat lost to the cylinder. Under ideal (adiabatic) conditions, the exponent would be 1.4, but a lower value, generally between 1.2 and 1.3 is used, since the amount of heat lost will vary among engines based on design, size and materials used, but provides useful results for purposes of comparison. For example, if the static compression ratio is 10:1, and the dynamic compression ratio is 7.5:1, a useful value for cylinder pressure would be (7.5)^1.3 × atmospheric pressure, or 13.7 bar. (× 14.7 psi at sea level = 201.8 psi. The pressure shown on a gauge would be the absolute pressure less atmospheric pressure, or 187.1 psi.)

The two corrections for dynamic compression ratio affect cylinder pressure in opposite directions, but not in equal strength. An engine with high static compression ratio and late intake valve closure will have a DCR similar to an engine with lower compression but earlier intake valve closure.

Additionally, the cylinder pressure developed when an engine is running will be higher than that shown in a compression test for several reasons.

  • The much higher velocity of a piston when an engine is running versus cranking allows less time for pressure to bleed past the piston rings into the crankcase.
  • a running engine is coating the cylinder walls with much more oil than an engine that is being cranked at low RPM, which helps the seal.
  • the higher temperature of the cylinder will create higher pressures when running vs. a static test, even a test performed with the engine near operating temperature.
  • A running engine does not stop taking air & fuel into the cylinder when the piston reaches BDC; The mixture that is rushing into the cylinder during the downstroke develops momentum and continues briefly after the vacuum ceases (in the same respect that rapidly opening a door will create a draft that continues after movement of the door ceases). This is called scavenging. Intake tuning, cylinder head design, valve timing and exhaust tuning determine how effectively an engine scavenges.

Compression ratio versus overall pressure ratio[edit]

Compression ratio and overall pressure ratio are interrelated as follows:

Compression ratio 2:1 3:1 5:1 10:1 15:1 20:1 25:1 35:1
Pressure ratio 2.64:1 4.66:1 9.52:1 25.12:1 44.31:1 66.29:1 90.60:1 145.11:1

The reason for this difference is that compression ratio is defined via the volume reduction:

\text{CR}=\frac{V_1}{V_2},

while pressure ratio is defined as the pressure increase:

\text{PR}=\frac{P_2}{P_1}.

In calculating the pressure ratio, we assume that an adiabatic compression is carried out (i.e. that no heat energy is supplied to the gas being compressed, and that any temperature rise is solely due to the compression). We also assume that air is a perfect gas. With these two assumptions, we can define the relationship between change of volume and change of pressure as follows:

P_1 V_1^\gamma = P_2 V_2^\gamma \Rightarrow
\frac{P_2}{P_1}= \left( \frac{V_1}{V_2} \right)^\gamma

where \gamma is the ratio of specific heats for air (approximately 1.4). The values in the table above are derived using this formula. Note that in reality the ratio of specific heats changes with temperature and that significant deviations from adiabatic behavior will occur.

See also[edit]

Notes[edit]

  1. ^ Encyclopædia Britannica, Compression ratio, retrieved 2009-07-21 
  2. ^ gSiteLife.Recommend("ExternalResource","110429942"); Tweet (2011-04-22). "2012 Mazda 3 gets 40-mpg SkyActiv engine option; diesel expected in 2014". Autoweek. Retrieved 2012-05-29. 
  3. ^ [1][dead link]
  4. ^ August 2010 BY DAVE VANDERWERP. "Mazda Engine News: Mazda Sky Gas and Diesel Details – Car and Driver". Caranddriver.com. Retrieved 2012-05-29. 
  5. ^ "Tractor Vaporising Oil". Web.archive.org. 2005-04-18. Retrieved 2014-08-10. 

External links[edit]



Original courtesy of Wikipedia: http://en.wikipedia.org/wiki/Compression_ratio — Please support Wikipedia.
This page uses Creative Commons Licensed content from Wikipedia. A portion of the proceeds from advertising on Digplanet goes to supporting Wikipedia.
266426 videos foundNext > 

Compression Ratio - Explained

What is compression ratio? An explanation of compression ratio; what it means and why it is important. Why some cars need premium fuel, and the advantages of...

All About Audio Compression Ratios - Into The Lair #81

In the 81st Into The Lair, Dave Pensado of Pensado's Place goes over everything you ever wanted to know about compression ratios (3:1, 4:1, 20:1 etc) and whe...

Compression Ratio and Thermal Efficiency

How does compression ratio affect efficiency? What determines an engine's efficiency? This video describes the direct correlation between compression ratio a...

Calculate Your Compression Ratio

This is everything you need to do to calculate your compression ratio. No foolin'. Every equation and process demonstrated. Find all your variables. Know you...

Pistons and Engine Compression Ratio - FAQ - Summit Racing Quick Flicks

This video covers the relationship between pistons and compression ratio. It includes the basic definition of compression, talks about the factors that deter...

Variable Compression Ratio Car Engine: MCE-5 VCR-i

Innovative MCE-5 VCR-i car engine (Variable Compression Ratio - intelligent compression ratio management) offers a set of outstanding features, as this video...

Compression Ratio

compression ratio.

How to measure and calculate your two strokes compression ratio

justin walks you through performing an installed cc measurement and a flat plate cc measurement along with squish band measurements and supplies you with the...

189 Calculating the Compression Ratio

59 Calculating Your Compression Ratio

Calculating Your Compression Ratio.

266426 videos foundNext > 

248 news items

IEEE Spectrum

IEEE Spectrum
Fri, 25 Jul 2014 09:04:12 -0700

“It is essentially the compression ratio and the ratio of the log of the compression time,” Misra explains, “but it then normalizes that number against an industry standard compressor used for the same data. For music, say, we'd use might use FLAC ...

Irish Independent

Irish Independent
Tue, 19 Aug 2014 18:30:00 -0700

They could catch on because they can store waste energy and then release it, like an electric motor and battery. And they cost a lot less than hybrid set-ups. • Variable Compression Ratio Engines: Basically an engine's compression ratio changes in line ...
 
AutoWeek
Wed, 20 Aug 2014 10:26:15 -0700

Direct injection helps keeps the cylinder and forged pistons cool. -- LT4 engines run a 10:1 compression ratio with aluminum alloy cylinder heads, a compact combustion chamber and titanium intake valve seats. The exhaust manifold is made from cast ...
 
Autocar
Thu, 21 Aug 2014 00:52:30 -0700

With an incredible 14:1 compression ratio thanks to a range of internal modifications and a rev limit of over 9000rpm, it thumps out not just more power than the regular 458 - in this case a whopping 597bhp - but also more torque, right across the ...
 
INAUTONEWS
Thu, 21 Aug 2014 02:45:00 -0700

... (Toyota Motorsport GmbH) and it has a 2.0 liter four-cylinder horizontally opposed boxer engine under its hood, which has been rated at 240 – 250 HP (179 – 186 kW), thanks to the modified engine software and the tweaked compression ratio and cam-lift.
 
iAfrica.com
Tue, 19 Aug 2014 21:56:40 -0700

Variable Compression Ratio Engines: Earlier this year, it was announced that manufacturers were developing engines with variable compression ratios. Although details of how this will be executed were not revealed, the principle has long been an ...
 
Popular Hot Rodding Magazine
Wed, 13 Aug 2014 06:18:45 -0700

These days, there are two schools of thought regarding compression ratio in a forced-induction engine: low compression and high boost, and high compression and high boost. Mixing a high static compression ratio with loads of boost used to be a recipe ...
 
Popular Hot Rodding Magazine
Tue, 19 Aug 2014 10:37:30 -0700

Achieving a compression ratio of 11.5:1 required a dished piston configuration. Note the D-dish arrangement, which retains the full function of the squish-quench area. The piston dish is a mirror image of the combustion chamber in the AirWolf cylinder ...
Loading

Oops, we seem to be having trouble contacting Twitter

Talk About Compression ratio

You can talk about Compression ratio with people all over the world in our discussions.

Support Wikipedia

A portion of the proceeds from advertising on Digplanet goes to supporting Wikipedia. Please add your support for Wikipedia!