digplanet beta 1: Athena
Share digplanet:


Applied sciences






















Early 20th-century alternator made in Budapest, Hungary, in the power generating hall of a hydroelectric station (photograph by Prokudin-Gorsky, 1905–1915).

An alternator is an electrical generator that converts mechanical energy to electrical energy in the form of alternating current. For reasons of cost and simplicity, most alternators use a rotating magnetic field with a stationary armature [1] but occasionally, a rotating armature is used with a stationary magnetic field; or a linear alternator is used. In principle, any AC electrical generator can be called an alternator, but usually the term refers to small rotating machines driven by automotive and other internal combustion engines. An alternator that uses a permanent magnet for its magnetic field is called a magneto. Alternators in power stations driven by steam turbines are called turbo-alternators.


Alternating current generating systems were known in simple forms from the discovery of the magnetic induction of electric current in the 1830s. The early machines were developed by pioneers such as Michael Faraday and Hippolyte Pixii.

Faraday developed the "rotating rectangle", whose operation was heteropolar - each active conductor passed successively through regions where the magnetic field was in opposite directions.[2] William Stanley, Jr. demonstrated the first practical system for providing electric illumination with the use of alternating current in 1886.[3] Both DC generators and the "alternator system" were used from the 1870s on.[4] Large two-phase alternating current generators were built by a British electrician, J.E.H. Gordon, in 1882. Lord Kelvin and Sebastian Ferranti also developed early alternators, producing frequencies between 100 and 300 Hz. In 1891, Nikola Tesla patented a practical "high-frequency" alternator (which operated around 15 kHz).[5] After 1891, polyphase alternators were introduced to supply currents of multiple differing phases.[6] Later alternators were designed for varying alternating-current frequencies between sixteen and about one hundred hertz, for use with arc lighting, incandescent lighting and electric motors.[7]

Principle of operation[edit]

Diagram of a simple alternator with a rotating magnetic core (rotor) and stationary wire (stator) also showing the current induced in the stator by the rotating magnetic field of the rotor.[citation needed]

A conductor moving relative to a magnetic field develops an electromotive force (EMF) in it, (Faraday's Law). This emf reverses its polarity when it moves under magnetic poles of opposite polarity. Typically, a rotating magnet, called the rotor turns within a stationary set of conductors wound in coils on an iron core, called the stator. The field cuts across the conductors, generating an induced EMF (electromotive force), as the mechanical input causes the rotor to turn.

The rotating magnetic field induces an AC voltage in the stator windings. Since the currents in the stator windings vary in step with the position of the rotor, an alternator is a synchronous generator.[1]

The rotor's magnetic field may be produced by permanent magnets, or by a field coil electromagnet. Automotive alternators use a rotor winding which allows control of the alternator's generated voltage by varying the current in the rotor field winding. Permanent magnet machines avoid the loss due to magnetizing current in the rotor, but are restricted in size, due to the cost of the magnet material. Since the permanent magnet field is constant, the terminal voltage varies directly with the speed of the generator. Brushless AC generators are usually larger machines than those used in automotive applications.

An automatic voltage control device controls the field current to keep output voltage constant. If the output voltage from the stationary armature coils drops due to an increase in demand, more current is fed into the rotating field coils through the voltage regulator (VR). This increases the magnetic field around the field coils which induces a greater voltage in the armature coils. Thus, the output voltage is brought back up to its original value.

Alternators used in central power stations also control the field current to regulate reactive power and to help stabilize the power system against the effects of momentary faults. Often there are three sets of stator windings, physically offset so that the rotating magnetic field produces a three phase current, displaced by one-third of a period with respect to each other.

Synchronous speeds[edit]

One cycle of alternating current is produced each time a pair of field poles passes over a point on the stationary winding. The relation between speed and frequency is N=120f/P, where f is the frequency in Hz (cycles per second). P is the number of poles (2,4,6...) and  N is the rotational speed in revolutions per minute (RPM). Very old descriptions of alternating current systems sometimes give the frequency in terms of alternations per minute, counting each half-cycle as one alternation; so 12,000 alternations per minute corresponds to 100 Hz.

The output frequency of an alternator depends on the number of poles and the rotational speed. The speed corresponding to a particular frequency is called the synchronous speed for that frequency. This table[8] gives some examples:

Poles RPM for 50 Hz RPM for 60 Hz RPM for 400 Hz
2 3,000 3,600 24,000
4 1,500 1,800 12,000
6 1,000 1,200 8,000
8 750 900 6,000
10 600 720 4,800
12 500 600 4,000
14 428.6 514.3 3,429
16 375 450 3,000
18 333.3 400 2,667
20 300 360 2,400
40 150 180 1,200


Alternators may be classified by method of excitation, number of phases,the type of rotation,and their application.[9]

By excitation[edit]

There are two main ways to produce the magnetic field used in the alternators, by using permanent magnets which create their own persistent magnetic field or by using field coils. The alternators that use permanent magnets are specifically called magnetos. In other alternators, wound field coils form an electromagnet to produce the rotating magnetic field.

All devices that use permanent magnets and produce alternating current are called PMA or permanent magnet alternator. A "permanent magnet generator" (PMG) may produce either alternating current, or direct current if it has a commutator. If the permanent magnet device makes only AC current, it is correctly called a PMA.

Direct connected DC generator[edit]

This method of excitation consists of a smaller direct-current (DC) generator fixed on the same shaft with the alternator. The DC generator generates a small amount of electricity just enough to excite the field coils of the connected alternator to generate electricity. A variation of this system is a type of alternator which uses direct current from the battery for excitation, after which the alternator is self-excited.[9]

Transformation and rectification[edit]

This method depends on residual magnetism retained in the iron core to generate weak magnetic field which would allow weak voltage to be generated. The voltage is used to excite the field coils for the alternator to generate stronger voltage as part of its build up process. After the initial AC voltage buildup, the field is supplied with rectified voltage from the alternator.[9]

Brushless alternators[edit]

A brushless alternator is composed of two alternators built end-to-end on one shaft. Smaller brushless alternators may look like one unit but the two parts are readily identifiable on the large versions. The larger of the two sections is the main alternator and the smaller one is the exciter. The exciter has stationary field coils and a rotating armature (power coils). The main alternator uses the opposite configuration with a rotating field and stationary armature. A bridge rectifier, called the rotating rectifier assembly, is mounted on the rotor. Neither brushes nor slip rings are used, which reduces the number of wearing parts. The main alternator has a rotating field as described above and a stationary armature (power generation windings).

Varying the amount of current through the stationary exciter field coils varies the 3-phase output from the exciter. This output is rectified by a rotating rectifier assembly, mounted on the rotor, and the resultant DC supplies the rotating field of the main alternator and hence alternator output. The result of all this is that a small DC exciter current indirectly controls the output of the main alternator.

By number of phases[edit]

Another way to classify alternators is by the number of phases of their output voltage. The output can be single phase, or polyphase. Three-phase alternators are the most common, but polyphase alternators can be two phase, six phase, or more.[9]

By rotating part[edit]

The revolving part of alternators can be the armature or the magnetic field. The revolving armature type has the armature wound on the rotor, where the winding moves through a stationary magnetic field. The revolving armature type is not often used.[9] The revolving field type has magnetic field on the rotor to rotate through a stationary armature winding. The advanatage is that then the rotor circuit carries much less power than the armature circuit, making the slip ring connections smaller and less costly; only two contacts are needed for the direct-current rotor, whereas often a rotor winding has three phases and multiple sections which would each require a slip ring connection. The stationary armature can be wound for any convenient medium voltage level, up to tens of thousands of volts; manufacture of slip ring connections for more than a few thousand volts is costly and inconvenient.

Specific applications[edit]

Automotive alternators[edit]

For more details on this topic, see Alternator (automotive).
Alternator mounted on an automobile engine with a serpentine belt pulley

Alternators are used in modern automobiles to charge the battery and to power the electrical system when its engine is running.

Until the 1960s, automobiles used DC dynamo generators with commutators. With the availability of affordable silicon diode rectifiers, alternators were used instead.

Diesel electric locomotive alternators[edit]

In later diesel electric locomotives and diesel electric multiple units, the prime mover turns an alternator which provides electricity for the traction motors (ac or dc).

The traction alternator usually incorporates integral silicon diode rectifiers to provide the traction motors with up to 1200 volts dc (dc traction, which is used directly) or the common inverter bus (ac traction, which is first inverted from dc to three-phase ac).

The first diesel electric locomotives, and many of those still in service, use DC generators as, before silicon power electronics, it was easier to control the speed of DC traction motors. Most of these had two generators: one to generate the excitation current for a larger main generator.

Optionally, the generator also supplies head end power (HEP) or power for electric train heating. The HEP option requires a constant engine speed, 900 rpm for a 480 volt 60 Hz HEP application, even when the locomotive is not moving.

Marine alternators[edit]

Marine alternators used in yachts are similar to automotive alternators, with appropriate adaptations to the salt-water environment. Marine alternators are designed to be explosion proof so that brush sparking will not ignite explosive gas mixtures in an engine room environment. They may be 12 or 24 volt depending on the type of system installed. Larger marine diesels may have two or more alternators to cope with the heavy electrical demand of a modern yacht. On single alternator circuits, the power is split between the engine starting battery and the domestic or house battery (or batteries) by use of a split-charge diode (battery isolator) or a mechanical switch. Because the alternator only produces power when running, engine control panels are typically fed directly from the alternator by means of an auxiliary terminal. Other typical connections are for charge control circuits.

Radio alternators[edit]

High frequency alternators of the variable-reluctance type were applied commercially to radio transmission in the low-frequency radio bands. These were used for transmission of Morse code and, experimentally, for transmission of voice and music. In the Alexanderson alternator, both the field winding and armature winding are stationary, and current is induced in the armature by virtue of the changing magnetic reluctance of the rotor (which has no windings or current carrying parts). Such machines were made to produce radio frequency current for radio transmissions, although the efficiency was low..

See also[edit]


  1. ^ a b Gordon R. Selmon, Magnetoelectric Devices, John Wiley and Sons, 1966 no ISBN pp. 391-393
  2. ^ Thompson, Sylvanus P., Dynamo-Electric Machinery. p. 7.
  3. ^ Thompson, Sylvanus P. "Milestones:Alternating Current Electrification, 1886". IEEE Global History Network. Retrieved 22 September 2013. 
  4. ^ "Generators". IEEE Global History Network. Retrieved 22 September 2013. 
  5. ^ US 447921 , Tesla, Nikola, "Alternating Electric Current Generator".
  6. ^ Thompson, Sylvanus P., Dynamo-Electric Machinery. pp. 17
  7. ^ Thompson, Sylvanus P., Dynamo-Electric Machinery. pp. 16
  8. ^ The Electrical Year Book 1937, published by Emmott & Co Ltd, Manchester, England, page 72
  9. ^ a b c d e Aviation Maintenance Technician Handbook—General (FAA-H-8083-30). Federal Aviation Administration. 2008. pp. 10_160—10_161. Retrieved 6 September 2013. 


  • Thompson, Sylvanus P., Dynamo-Electric Machinery, A Manual for Students of Electrotechnics, Part 1, Collier and Sons, New York, 1902
  • White, Thomas H.,"Alternator-Transmitter Development (1891-1920)". EarlyRadioHistory.us.

External links[edit]

Original courtesy of Wikipedia: http://en.wikipedia.org/wiki/Alternator — Please support Wikipedia.
This page uses Creative Commons Licensed content from Wikipedia. A portion of the proceeds from advertising on Digplanet goes to supporting Wikipedia.
398287 videos foundNext > 

How does an Alternator Work ?

This video gives an elaborated explanation on working of Alternators/ AC Generators with help of animation. Alternators are also referred as Synchronous gene...

Diagnosing Alternator Problems - EricTheCarGuy

Visit me at: http://www.ericthecarguy.com/ I got together with my friends from BBB Industries on this one, we managed to put together a pretty comprehensive ...

Alternator DEMO Wiring, connection to Battery, Capacitors, Inverter, Modification

DO NOT TRY THIS AT HOME.....This video is just for entertainment and educational purposes. Alternator demo using a Delco CS alternator, this alt has a built ...

How a car alternator works EASY TO UNDERSTAND!!! laymans terms ..

General overview of how an alternator works..how an automotive alternator works tutorial autoshop 101 . Engineering Explained . How An Alternator Works . Bri...

How to make an electric axial flux alternator - DIY

This video shows the method I used to make my first electric generator. It is a miniature axial flux generator to test the solutions I have selected on the w...

Alternator Demo, self energize, generator, arc welder

DO NOT TRY THIS AT HOME.... The video is just for entertainment and educational purposes. In this video I'm using a GM Delco Remy 10 DN alternator 1967-1972,...

How Alternators work, and how you can tell when they go bad

ill show you how to test your alternator and ill explain how they work. After you watch this you'll have a much better understanding of what the cars alterna...

How to Change (remove & replace) an Alternator

Follow these simple, step-by-step instructions for removing and installing an automobile alternator with common tools. Includes advice on the correct wiring ...

Mitsubishi alternator repair / brush change. Fits Pajero, Kia,Pegeot and many more.

Please visit my Ebay shop: http://stores.ebay.ie/goldlion-autoelectrics Hello guys, In this Video i ame showing you how to solve a common problem with a mits...

INDUCTION MOTOR DIY hack Alternator 40 watt low 800 RPM Neodymium Motor Generator Conversion

http://greenpowerscience.com/ALTERNATOR1.php This is a long video but shows the complete basic steps for creating an alternator from a standard AC electric m...

398287 videos foundNext > 

1889 news items


Fri, 25 Jul 2014 07:17:38 -0700

The National Highway Traffic Safety Administration has opened an investigation into an estimated 123,000 2011-'12 Dodge Charger cars after consumer complaints of alternator failure. NHTSA said it has "identified 14 complaints alleging incidents of ...


Tue, 29 Jul 2014 04:26:15 -0700

To assess the impact on the overall vehicle and electrical system, Remy collected real-time operating data on several vehicle applications. Data shows that, over a typical life cycle, there is a fuel cost savings as alternator efficiency increases 60 ...
AftermarketNews.com (AMN)
Tue, 29 Jul 2014 08:52:29 -0700

PENDLETON, Ind. – Remy International has announced the launch of the Delco Remy 38SI, its latest high-output alternator. With this high-efficiency, mid-range amperage alternator, Remy offers customers a comprehensive portfolio of high-output products.
Wall Street Journal
Tue, 29 Jul 2014 04:26:15 -0700

To assess the impact on the overall vehicle and electrical system, Remy collected real-time operating data on several vehicle applications. Data shows that, over a typical life cycle, there is a fuel cost savings as alternator efficiency increases 60 ...

Auto World News

Auto World News
Fri, 25 Jul 2014 08:56:15 -0700

The National Highway Traffic Safety Administration has opened an investigation into an estimated 123,000 2011-'12 Dodge Charger cars after consumer complaints of alternator failure. (Photo : Fiat Chrysler Automotive ). Safety regulators have opened an ...
Fri, 25 Jul 2014 10:47:25 -0700

Sen. Claire McCaskill, D-Mo., to GM CEO Mary Barra: 'The failure of your legal department is stunning' - @Lebeaucarnews. End of alert. General Motors recalls 2014. 14:37. Delphi CEO prepared remarks: Ignition switch was responsibility of General Motors ...


Wed, 09 Jul 2014 09:41:15 -0700

The AVi2800 internal fan alternator is ideal for high-performance aftermarket retrofit upgrades, particularly within older model school buses and heavy trucks, or in applications where weight reduction, higher temperature and higher power are target goals.

The Nation

The Nation
Mon, 14 Jul 2014 10:03:45 -0700

Sigma & Hearts, a leading automotive-parts maker with operations in Thailand and Indonesia, is discussing with Bosch, Valeo, and other global companies the joint development of a key component using its patented process developed in Thailand.

Oops, we seem to be having trouble contacting Twitter

Talk About Alternator

You can talk about Alternator with people all over the world in our discussions.

Support Wikipedia

A portion of the proceeds from advertising on Digplanet goes to supporting Wikipedia. Please add your support for Wikipedia!